Replacement Roof Vent Cover for Philips V2100 Trailer Roof Vent

Question

Question:

I need to know which domes can be used to replace the domes on Phillips V2100 roof vents. Thank you

asked by: Roger

1

Helpful Expert Reply:

Ventline offers a wide assortment of trailer vent replacement parts for both their own Ventline-branded products as well as many others' OEM parts. We do not offer any Phillips-brand vent parts but there is a strong chance that you'll be able to find a Ventline item that will work for you.

You can use the link provided to view our main page for trailer vent covers; these are offered in various materials and colors.

The main factor to consider is the type of hinge on your vent. Our replacement covers are offered in three hinge types: 3-point, 4-point and continuous hinges. Since most roof vents share common dimensions (14 x 14) the hinge type selection (which can be made in the left margin) will narrow the results to just those items with the type of hinge you need and from there you can select the appropriate color.

expert reply by: Adam R

1

Answer 1

We do have the correct replacement fan motor and blade for your Ventline V2100 roof vent, which are the following: - Replacement 12V DC Motor for Ventline, Ventadome, and Vanair Fans #BVD0218-00 - Replacement Fan Blade for Ventline Ventadome Trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Roof Vent Cover for Philips V2100 Trailer Roof Vent

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching