Parts Needed to Add 7-Way and Brake Controller to 2025 Ford Escape

Question

Question:

I need to add 7 pin wiring with brake compatibility to my 2025 Ford Escape. It did not come with any tow package/wiring. I was looking at the universal kit part 22551, is this the best option for my vehicle type? if so, do I need to get a brake modulator as well?

asked by: Katlyn O

0

Expert Reply:

Hey Katlyn, I have a similar solution that is going to be a little easier to install with first starting with the 4-way kit part # TK57CR as this will not require quite as much wiring since it installs by plugging inline with your taillight harnesses instead of requiring you to hardwire to them like with the # 22551.

Then from there you would have to adapt it to a 7-way with the # ETBC7 which also comes with whats needed to wire in a brake controller as well. For a brake controller I really like the Redarc Tow Pro Liberty # RED52VR as it's proportional and can sense how hard you are applying the brakes and it only puts a small knob on the dash of your vehicle as well. What are you going to be towing?

expert reply by: Jameson C

0

Katlyn O.

2/11/2026

It is a small pop-up camp trailer, weighs 1,850lbs.

Jameson C.

2/11/2026

@KatlynO right on! Yeah so maybe you don't actually need a brake controller. Instead of the ETBC7 you'd want the part # 37185 then.

Katlyn O.

2/11/2026

@JamesonC It does have electric trailer brakes so I think the original parts you listed are great! Thank you for your assistance, it was very helpful!!

Jameson C.

2/11/2026

@KatlynO No prob! Glad to help!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Parts Needed to Add 7-Way and Brake Controller to 2025 Ford Escape

Products Featured in This Question

Continue Researching