How to Attach a Rhino-Rack Pioneer Platform Roof Tray to BillieBars

Question

Question:

Looking at Rhino-Rack Pioneer Platform Roof Tray - Aluminum - 59 Long x 54 Wide for a 2025 Ford Ranger. Will this work with installed Billiebars? Does the rack include mounting hardware for the Billiebars? Thanks.

asked by: David B

0

Expert Reply:

It sure will David. To attach the Rhino-Rack Pioneer Platform Roof Tray item # RR27AP to a set of BillieBars you'll need the Pioneer Platform Mounting Kit for Rhino-Rack Heavy-Duty Crossbars item # RR43105. They're going to adapt the platform's base to the square profile of the BillieBars. You'll need two sets of the item # RR43105, one for each crossbar.

What kind of gear do you plan on putting on the Pioneer tray?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

RR43105
(click to enlarge)

David B.

1/19/2026

Just several Roam cases for now — 86L & 93L. Thanks for the info. I was thinking the Rhino brackets would work but wanted your opinion.

Jerred H.

1/19/2026

@DavidB Right on! The Platform Rack item # RR27AP will definitely accommodate them. You're welcome! Two sets of the item # RR43105 will indeed work. We've had quite a few people use these successfully over the last couple years.

Answer 1

The Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers #PE99CV does not come with great instructions. In order to install the Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers #PE99CV, you will need to…

view full answer...

Answer 2

Hey Colin, yes the Pioneer Platform Mounting Kit for Rhino-Rack Heavy-Duty Crossbars #RR43105 could be used to attach a Pioneer Platform to the Billie Bars since they are a square load bar. Basically this kit wouldn't work with aero bars due to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

How to Attach a Rhino-Rack Pioneer Platform Roof Tray to BillieBars

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching