Can Log Splitter Trailer with Integrated Hub/Wheels be Replaced with Standard Hubs

Question

Question:

Hi, Im looking to convert my log splitter to a conventional trailer hub setup so I can run a more standard 4 or 5 lug 8 wheel, instead of the current wheels, which have the wheel bearings integrated into them. My issue is, the spindles are straight 3/4 diameter, and Im having a hard time finding idler hubs for 3/4 spindles. Would you be able to help with this? Thanks, Matt

asked by: Matt

0

Expert Reply:

Hey Matt, we don't have any hubs that are designed to fit a 3/4 inch straight spindle like what you have.

You could weld on new spindles like the part # TRU44FR so that you could fit standard hubs if that would be something you'd be interested in?

expert reply by: Jameson C

0

Matt

9/29/2025

Thank you Jameson, I appreciate the info! Welding on new spindles is definitely an option, I was just looking to see if I happened to be missing something in my search for 3/4" spindle hub/bearing setups. Thank you for your help! Matt

Jameson C.

9/29/2025

@Matt Glad to help! Make sure you have the correct jigs for welding on spindles so that the alignment stays good.

Answer 1

Based on your dimensions you have a BT8 style hub so the part #AKIHUB-440-2-1K you mentioned would fit and work well. The length of your spindle matches what this is compatible with as well.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Can Log Splitter Trailer with Integrated Hub/Wheels be Replaced with Standard Hubs

Product Page this Question was Asked From

Continue Researching