Trailer Wiring Harness for 2013 Volkswagen Golf

Question

Question:

Looking for a wiring harness/converter with flat four To install In 2013 VW golf. Also rather than run a wire clear through the car to battery cannot one just use the rear power socket?

asked by: David M

0

Expert Reply:

Hi David; the Curt Powered Tail Light Converter # C59236 you looked at will fit your 2013 VW Golf. There are no custom wiring harnesses available so the universal splice in is the only option. Also, you need to run the wire straight to the battery. It would be nice if the power socket at the rear worked but that circuit will likely end up overloaded and you don't want to damage your vehicle wiring and have other issues from it.

Are you towing a trailer or do you need to power lights on an accessory?

expert reply by: Robin H

0

Curt Powered Tail Light Converter
(click to enlarge)

Robin H.

9/29/2025

Hi David, did you decide to go with the Curt Powered Tail Light Converter for your VW Golf? I'm curious if it worked well for your towing or lighting needs, as your experience could help others in a similar situation.

David M.

10/7/2025

@Robin Yes I went with the wh63265 kit which upon arrival was confusing because it comes as a two part kit with two separate part #s neither of which say wh63265. The part I dreaded was running the power wire to battery It wasn't that bad, but I did not run it undercarriage, but rather under door sills and thru an existing main wiring grommet. I used the ' fish wire' method by taping 12v wire to a straight piece of coathanger thru said grommet Much easier to remove battery and pull thru from engine bay Grommet is right behind battery. Only difficulty then was determining brake and stop wires Wish it had been plug and play as on 2016 VW golf as opposed to my 2013. But all good now. Allow three hours because you have to figure out how to undo door sills and rear fender panels .

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Trailer Wiring Harness for 2013 Volkswagen Golf

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching