Curt Hitch #13408 Replacement Hardware Recommendation

Question

Question:

Where can I obtain a replacement parts for the Curt Hitch #13408? Specifically looking for items 5 CM-SP10 Square Hole Spacer and 7 Carriage Bolt. Thanks.

asked by: Luther M

0

Expert Reply:

Replacement hardware is available. You will need part # RHK. Once on the product page, just type in the Hitch Item Number in the box on the right. Then use the pull down menu below that to select the manufacturer. Then just click the Add to Cart button and you will be done.

Hitch hardware is one-only. So you if you are trying to install this hitch on a second vehicle you would want to use all new hardware.

expert reply by: Jameson C

0

Answer 1

Hey Chad, I really like the Curt hitchpart #C34UR for your 2025 Toyota Corolla LE as we have found that the Curt hitches have the best quality. This would also not reduce your ground clearance enough to cause issues with speed bumps either. What are…

view full answer...

Answer 2

Hey David, so we have complete replacement hardware kits for the hitches we carry with the part #RHK but we also sell the fishwire by itself with the part #C58400. If it's a new hitch and you never found the hardware try looking in the hitch…

view full answer...

Answer 3

Both the Draw-Tite #76226 and the Curt #C13316 are fits for the 2015 BMW X3. Both hitches are pretty much on par as far as quality goes. The Draw-Tite does have a higher tongue weight and towing capacity as you mentioned, but you'd be limited to…

view full answer...

Answer 4

While we don't have just the CM-SP12 spacers for the Curt Trailer Hitch Receiver #C13362, you can either get a complete replacement hardware kit with part #RHK or you can just get 2 of the Trailer Hitch Spacer Block - 3" Long x 1" Wide…

view full answer...

Answer 5

The biggest difference between Curt Hitch #13430 and #13408 is that the #13430 has a round cross tube whereas the #13408 has a square cross tube. This difference is primarily an aesthetic difference since both of these hitches have the same towing…

view full answer...

Answer 6

From what I have found, there are four bolts holding the fuel tank in place at the back of your 2001 Jeep TJ. The Curt Trailer Hitch Receiver #13408 covers these bolts once it is installed, so it would have to be uninstalled in order to access them…

view full answer...

Answer 7

Both the Curt hitch part #13408 and the part #13430 would work well on your 2002 Jeep Wrangler. Both have the same capacities and have 2 inch openings. The differences are that the #13408 uses a different attachment method like you noticed and has a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hello Chris, You can run the Patriot off an auxiliary 12V battery, but it’s not something I’d recommend as a long-term solution. The unit is designed to pull from the Jeep battery, and the draw is actually pretty low. If your battery is going dead…

view full answer...

Answer 10

The base plates you can install on your Jeep depend on the bumper style you have. If you have a U-channel bumper the base plates that will work are part #1417-1. If you have an off-road bumper with the 1-inch D-Ring bumper mounts then the base plates…

view full answer...

Answer 11

We have three Roadmaster base plate fits for the 1998 Jeep Wrangler TJ with the u-channel bumper that appear on the linked page. These items are the fixed-install Classic #1417-1, and the kits with removable arms, EZ5 #RM-521424-5 and the EZ4 kit…

view full answer...

Curt Hitch #13408 Replacement Hardware Recommendation

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching