Replacement for Venture M-9000-PK Landing Gear Motor

Question

Question:

I have a 5the wheel trailer and the motor that lifts and lowers the legs needs replaced. The part number on the motor is M9000PK. Do you offer a replacement motor for that.?

asked by: Chris E

0

Expert Reply:

Hey Chris! The correct replacement for your old Venture M-9000-PK is the Replacement Motor for Stromberg Carlson Electric Landing Gear # LG-142178.

Any big trips planned for the fall with your 5th wheel?

expert reply by: Robin H

0

Replacement Motor
(click to enlarge)

Robin H.

9/12/2025

Hey Chris, did the replacement motor for your 5th wheel work out for you? I'd love to hear your outcome, as it could give others confidence when ordering replacements.

Answer 1

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Answer 2

Hey Bill, Adding a second motor is not going to increase the weight capacity. It may increase the travel speed, but the weight capacity is determined by the structural components and gears of the landing gear. A second motor is not going to make…

view full answer...

Answer 3

To determine the correct landing gear repair kit for your trailer you will need to know the what make and model landing gears are installed. If you have a set of Lippert Components Venture landing gear, then the #LC146060 for the follow leg and…

view full answer...

Answer 4

From online research, yes, as it looks like your 2005 Keystone Raptor 5th Wheel most likely has the Venture landing gear system. I highly recommend you verify this before ordering though. The Lippert Electric Landing Gear Set, #LC333964 has outer…

view full answer...

Answer 5

The price difference does seem backwards, but the faster speed part #LG-141893 has the same weight capacity as the lower speed part #LG-142178 that you also referenced. It's a difference of 5,500 RPM and 7,140 RPM so you would definitely see a…

view full answer...

Answer 6

If you know you need the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear #LC276602 then the correct motor would likely be Lippert Components Venture 5th Wheel RV Landing Gear Motor #LC142178 which is for Venture landing…

view full answer...

Answer 7

To replace your existing Venture motor, the Lippert Components Venture 5th Wheel RV Landing Gear Motor #LC142178 is the correct replacement part for you. For an aluminum gear box, you are correct that you can use part #LG-179015. The #LC142178 motor…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement for Venture M-9000-PK Landing Gear Motor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching