Are Weigh Safe Flap Jacks Stackable

Question

Question:

Can you stack these blocks? For example a 2inch on top of a 8inch or an extreme 8inch on top of a 8. Are they made to interlock with each other?

asked by: Daryl H

0

Expert Reply:

Hey Daryl, I checked with Weigh Safe and the Flap Jacks like the part # WS88ER are not designed to be stacked. Are you in need of something 10 inches tall?

expert reply by: Jameson C

0

Jameson C.

9/2/2025

Hey Daryl, did you find a solution for your stacking needs with the stabilizing blocks? If you're still looking for a solution, I'm happy to help.

Answer 1

Your Dexter D44 Axle number 635096 uses the Trailer Hub and Drum Assembly #8-407-5UC3-EZ that comes preloaded with the Races #LM67010 and #L68111. It does include the Bearings #L68149 and #LM67048, Grease Seal #58846, Grease Cap #21-42-1 and lug…

view full answer...

Answer 2

Hey Chris, since we know your 2024 Brinkley Z3100 has tandem 7k axles that have an 8 lug bolt pattern you would want the Hydrastar kit part #HSE7K-T1SO which comes with everything you'd need while also having the best and most reliable actuator…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Are Weigh Safe Flap Jacks Stackable

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching