Will the Reese Chain Hangers Work w/ the Curt MV Weight Distribution System?

Question

Question:

Will these Reese chain hangers work with part C17051 Curt MV Weight Distribution System - Round Bar - 8,000 lbs GTW, 800 lbs TW? I have a v-nosed cargo trailer that doesn’t have room for the clamp on brackets Thank you

asked by: Dave W

0

Expert Reply:

Yes, they are Dave! The Chain Hangers for Reese Weight Distribution Systems item # RP58305 are exactly what you need if you don't have room for the brackets with the Curt item # C17051.

What do you haul in your cargo trailer?

expert reply by: Jerred H

0

Answer 1

You could use a friction sway control device like #83660 to help control the sway effects caused by passing trucks, but with a 24-foot enclosed trailer that has a lot of surface area for wind to push on, you will get much better results with a weight…

view full answer...

Answer 2

The Replacement Ball and Plate Assembly part #C17201 should work just fine for your Jayco Jay Flight SLX 8 whether you have theReese Friction Sway Control Kit part #83660 or the Curt Friction Sway Control for Weight Distribution Systems part #17200.…

view full answer...

Answer 3

Thanks for the picture Chris! The lift-brackets mount about 29" back from the center of the coupler on the Blue Ox SwayPro Weight Distribution w/ Sway Control item #BXW0553. It looks like your trailer's tongue isn't going to have…

view full answer...

Answer 4

The Pole-Tongue Adapter for Equal-i-zer Weight Distribution Systems part #EQ95-01-5950 is designed to be used on straight-tongue trailers and would not work with your a-frame trailer. Since you said that the tongue of your a-frame is covered by the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Will the Reese Chain Hangers Work w/ the Curt MV Weight Distribution System?

Products Featured in This Question

Continue Researching