American Made Lunette Ring that Fits a 3" Wide Channel

Question

Question:

which Lunette ring is made in USA that you have listed ?

asked by: Darrin R

0

Expert Reply:

The Demco Lunette Ring item # DM09557-81 is made in the USA. It fits a 3" wide channel bracket and has a 25,000 lbs capacity. It has a inner diameter of 3" and an outer diameter of 6".

What of lunette ring are you looking for?

expert reply by: Jerred H

0

Jerred H.

8/7/2025

Hey, did the Demco Lunette Ring made in the USA work out for your needs? I'm curious because it could help others who are looking for a similar solution!

Answer 1

Hello David, thanks for reaching out. It is possible to switch your trailer over to a lunette ring/pintle hitch system. Basically you will need to replace your current A-frame coupler with a channel coupler like part #LR76VR. This will allow you to…

view full answer...

Answer 2

Thanks for the picture Richard, I can tell by your picture you have a Model 6 surge actuator on your trailer which the #T4846500183 is the correct replacement for if you were wanting a channel style inner slide member replacement.

view full answer...

Answer 3

Grade 8 bolts are recommended for installing the Buyers Products 3" I.D. Heavy-Duty Forged 4-Bolt Mount Lunette Ring #337BDB1394 that you referenced. We actually have a mounting kit for this with part #3378530 that includes the bolts. Then for a…

view full answer...

Answer 4

Although we do offer the mounting kit #3378530, there are no specific plates we carry capable of handling the same capacity as the #337PH30. The only option would be the Buyers Products Weld-On Pintle Hitch Plate #3371809027A. However, this would…

view full answer...

Answer 5

Hey Carlos we do have a good solution for converting the 2" ball coupler on your trailer to a lunette ring. What I recommend is the Demco 5-Position Adjustable Channel Bracket #DM13867-52. This can be bolted to a 3" wide trailer tongue and…

view full answer...

Answer 6

Yes, you can use the Pintle Hook Mount, #63059, in either a rise or drop position. If you need a bolt on pintle hook, use #C48205. It has a 10,000 pound capacity so it has more than enough capacity for your trailer.

view full answer...

Answer 7

When using a Pintle Ball combination hitch like the #PH1 , a certain amount of slack is inevitable because the opening is much larger than if you were using a standard pintle hitch. If you're not already using the 2-5/16" hitch ball, I would…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

American Made Lunette Ring that Fits a 3" Wide Channel

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching