How Do I Calibrate The Redarc Tow Pro Link Bluetooth Brake Controller?

Question

Question:

How long does calibration take and do I need to do it every time I tow?

asked by: Marc

0

Expert Reply:

Hey Marc! Calibration for the Redarc # RED57AR only takes a few miles if in town, maybe a little longer if you aren't making frequent stops as it sometimes takes 15-20 braking applications. It’s fully automatic and uses internal sensors to detect motion and orientation. Once it’s set up, you don’t need to recalibrate unless you remove the unit or change vehicles. We recommend giving it a test squeeze on the override/sway button just to confirm its dialed in each trip.

Jacob from Kentucky said his calibrated on his way out of the campground before he even left the twisty park road. I attached an image from the instructions to show you the exact details that Redarc gives us.

expert reply by: Andrew N

0

Redarc Tow Pro Link Active Callibration
(click to enlarge)

Denise

7/7/2025

What if I’m switching between two different trailers? one’s a lightweight utility trailer and the other is a 28-foot camper. Do I need to recalibrate every time I swap trailers, or does it remember settings for each?

Andrew N.

7/7/2025

@Denise Great question, Denise. The Redarc Tow-Pro Link doesn't require a full recalibration when swapping trailers; calibration is vehicle-specific, not trailer-specific. So as long as the controller stays in the same vehicle and hasn't been unplugged or moved, you're good to go. That said, we do recommend adjusting your gain settings in the app each time you switch trailers. Lighter trailers need less braking force, while heavier ones like your 28-foot camper will need more. The good news is the app lets you save presets, so you can quickly switch between them before hitting the road. You can also easily adjust by using the remote in the cab by following this: Press the Minus or Plus Buttons to adjust the braking force between 0 (off) and 10 (maximum). Each press adjusts the Braking Force by 0.5 The current level is displayed by the LEDs As a safety feature, if you reduce the Braking Force below 3, you must test the brakes at the new level within 30 seconds. If you try to reduce the Braking Force below 3 without first applying the brakes, the Braking Force will remain at level 3 Let us know the weight of each trailer and we can help you dial in a solid starting point for both. Safe travels!

Herb

10/3/2026

What should the gain be set at for a 4000lb camper for on the highway towing

Andrew N.

10/5/2026

@Herb Hey Herb, there is not a specific setting for a trailer size or weight, but Redarc says to start on a low setting like 3 or 4 and adjust from there as needed. So you can set up the controller and let it callibrate, and start at about 3 or 4 and go on a test drive with the trailer. If it feels like your truck is still doing the majority of the braking and it could use more help, like at stop signs or stop lights, then up it a bit to 5 or 6 etc. If it feels like the trailer is pulling you back or locking up the tires, then dial it back. I imagine you'll want somewhere in the middle like 5 or 6.

Answer 1

Hey Eric; there are no specific instructions for the installation of Redarc brake controllers like the Tow-Pro Liberty #RED52VR on a 2024 Tacoma. Your Tacoma doesn't have a custom wiring harness since there is no port for the brake controller…

view full answer...

Answer 2

Check the back of your factory 7-Way on your 2017 Nissan Frontier. If you can pull the wiring harness off of the back of it and it looks like #HM40950 on the inside where that harness plugs in then you can just swap out your 7-Way with #HM40950. I…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

How Do I Calibrate The Redarc Tow Pro Link Bluetooth Brake Controller?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching