Looking for Replacement Cap for B&B RV Fresh Water Gravity Fill Inlet # BM68RR

Question

Question:

part BM68RR water tank for camper cap and houseing cap missing i have pic no where to send

asked by: Barry M

0

Expert Reply:

Hey Barry, if you have the part # BM68RR and are looking for a replacement cap for it you would want the part # BM36MR. Is this what you were looking for?

expert reply by: Jameson C

0

Jameson C.

9/2/2025

Hey Barry, did the replacement cap I suggested work out for your water tank? I'm asking because your experience could help others in a similar situation.

Answer 1

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 5

Welcome back Rick. The Rubber Half Round Seal item #SR85FR, which is 3/4" wide x 11/16" tall, is the closest seal I have that looks like the .5 KINRO 239421 seal you need. I couldn't find any dimensions off of Jayco's website so…

view full answer...

Answer 6

Hi Corde; what is on the other end of your pigtail? Is it 1/4" male NPT? If it is, you can use the MB Sturgis Propane Pigtail w/ Back Check - RV Type 1 x 1/4" Male NPT - 2' #100473-24-MBS as a replacement.

view full answer...

Answer 7

The gray cap of the #A01-1117VP is threaded so you'd need to start by unscrewing it so that you can access the internal components of the #A01-1117VP to rebuild it with the kit #A01-1112.

view full answer...

Answer 8

We can get you a replacement for your TDE LP75 disc brake actuator; that's a 7,500 lb actuator that accepts a 2" hitch ball, and the correct option will depend on if your trailer tongue is 3" wide x 4" tall or 3" wide x…

view full answer...

Answer 9

The only tank equipped RV water heat option we currently offer is the Dometic RV Water Heater part #DMC74FR which is a 120 volt unit with 6 gallon tank and gas/electric operation. In regards to installation, this must be performed by a qualified…

view full answer...

Answer 10

Atwood Water Heaters like your G6A-7 #AT96110 does not use an anode rod because the tank is made of plastic. There is no need for it as the tank will not corrode. If you want to use one, you can use the Camco RV Water Heater Anode Rod - Magnesium -…

view full answer...

Answer 11

Hey, Chris. The fittings between B&B RV Winterizing Diverter Valve part #BM65RR and B&B RV Hot Water Tank Bypass Diverter Valve part #BM95RR are the same, 1/2". The face plates between will have different labeling but the valves…

view full answer...

Looking for Replacement Cap for B&B RV Fresh Water Gravity Fill Inlet # BM68RR

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching