How is Valterra Water Pressure Regulator Disassembled to Install Rebuild Kit

Question

Question:

Water pressure rebuild kit how do I get the insides out of a valverde water pressure to replace it

asked by: John G

0

Expert Reply:

The gray cap of the # A01-1117VP is threaded so you'd need to start by unscrewing it so that you can access the internal components of the # A01-1117VP to rebuild it with the kit # A01-1112.

expert reply by: Jameson C

0

Answer 1

I recommend upgrading to the Valterra Adjustable Water Regulator #A01-1117VP. It uses a higher quality gauge and they offer a Replacement Gauge #A01-1125 in the event it is damaged. You will also be able to adjust your water pressure with this…

view full answer...

Answer 2

I contacted the Tech Rep for this product, the Valterra Adjustable Water Regulator for RVs, #A01-1117VP. He stated that incoming water pressure will of course have an affect on the rating but, you can expect an approximate flow rate of about 12 GPM.

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 7

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Hey Tom, congrats on the new truck! Typically when we hear that someone has the OEM tow prep package they mean the puck system. This is going to be five circular holes built into the bed of your Ram truck and is by far the best way to attach a 5th…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 12

When installing the pivot arms on your B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package - Dual Jaw - 25,000lbs Item #BWRVK3600 you'll want to ensure that you have 6" of clearance between the bed rails and the nose of your…

view full answer...

How is Valterra Water Pressure Regulator Disassembled to Install Rebuild Kit

Product Page this Question was Asked From

Continue Researching