Will Inno Square Bar Feet Work w/ Older Thule Square Bars?

Question

Question:

Will the Inno INFR feet fit the older Thule square bars? Thank you

asked by: George

0

Expert Reply:

Yes, they can so long as your Thule square bars don't have slots on the bottom. The Inno Feet for Square Crossbars item # INFR work with the Thule square bars that measure 7/8" tall x 1-1/4" wide.

The Inno Feet item # INFR will fit the raised rails on a 2023 Subaru Outback wagon. What are you planning on using your roof rack for?

expert reply by: Jerred H

0

George V.

6/26/2025

Jerrod, I want to mount my 78” long square Thule bars to my 2023 Subaru Outback Limited utilizing the aluminum corners on the factory rack, and need a mount that has a strap that will wrap around those corners on the factory rack. Thule use to make a 450 mount that would do that but they discontinued them.

Jerred H.

6/27/2025

@GeorgeV Those are really long crossbars for a 2023 Subaru Outback Limited! The recommended size is 50" long like the Thule SquareBar Evo Roof Rack for Raised Rails item # TH84ZA. The closest thing I have to what you're describing that is compatible with Thule square bars is the item # INFR.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Will Inno Square Bar Feet Work w/ Older Thule Square Bars?

Product Page this Question was Asked From

Continue Researching