Do You Carry a Replacement Light for My Vison Red Clearance Light Part Number CL-26010-R?

Question

Question:

I’m looking to replace a light on my trailer. It’s a vision led CL-26010-R. Any chance you can help me acquire one or get me an equivalent?

asked by: Spencer A

0

Expert Reply:

Hello Spencer,

The best replacement that we have for the vision led CL-26010-R, is the Peterson Clearance or Side Marker Trailer Light w/ Reflector - Submersible - Round - Red Lens # M143R. When I go to the link that you provided me with, I see that their thickness is listed at 7/8", our # M143R is listed at 11/16" but we only measure the actual lens. When I watch the video and look to where the ruler is, if we were to measure the thickest part (to the far end of the connectors on the back) it is actually 7/8".

Your original grommet and pigtail will work with this light as well.

What kind of trailer is this going on?

expert reply by: Kate F

0

Thickness Measurement on # M143R
(click to enlarge)

Spencer

6/9/2025

Thanks for the reply. The trailer is an echo 3 rail motorcycle trailer.

Kate F.

6/9/2025

@Spencer Very nice Spencer. I used to spend a lot of time on the back of a bike, always wanted to learn to ride my own. I suppose I'm not dead yet so there is still the possibility. I like to spend a lot of my extra time out on the water these days. Stay safe out there =)

Answer 1

Hey Michael, the SAE number of a trailer light isn't always the best way to pick out a replacement light since that isn't a part number. But most likely you are looking for a #A32RB which measures 4 inch by 2 inch and is red and for amber…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Do You Carry a Replacement Light for My Vison Red Clearance Light Part Number CL-26010-R?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching