Ball Mount with 4 inch Rise Recommendation for Use with Curt Hitch for 2003 Lincoln Town Car
Updated 06/04/2025 | Published 06/03/2025
Products Featured in This Question
Question:
13707 Looking for a recommendation for the proper 2 hitch adapter with rise and length configuration to clear the rear bumper and match a roughly 14.5-15.0 inch trailer tongue on 2003 Lincoln Town Car using the 13707 hitch linked above.
asked by: Justin S
Expert Reply:
Hey Justin, when we installed the Curt hitch part # 13707 on a similar 2004 Lincoln Town Car to your 2003 model we found that from the top of the hitch opening to the ground measured 11 inches. So the correct amount of rise you'd want would be right at 4 inches like the ball mount # D-28 which also happens to be a longer ball mount so it would also not interfere with your rear bumper.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Transmission Cooler
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Installing the Curt Trailer Hitch Receiver on your 2007 Ford Crown Victoria
- Shop: Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Shop: Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class III - Efficient
- Search Results: brake controller
- Q&A: Transmission Cooler and Suspension Enhancement for a 2011 Toyota Sienna
- Q&A: Transmission Cooler Installation Tips for a 1994 Mercury Grand Marquis LS
- Q&A: 2023 Honda Passport Touring Edition Transmission Cooler Recommendation
- Q&A: Transmission Cooler Recommendation for 2011 Chevy Silverado
- Q&A: Location of Transmission Lines on a 2001 Ford Ranger For addition of a Transmission Cooler
- Search Results: transmission cooler
- Q&A: Replacement Hitch Hardware Recommendation for a 2003 Mercury Grand Marquis
- Video: Set up: Curt Trailer Hitch Receiver on a 2006 Mercury Grand Marquis
- Shop: Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches
- Shop: TowSmart Ball Mount for 2" Hitches - 4" Rise, 5-1/4" Drop - 5,000 lbs
- Shop: Master Lock Hitch Receiver and Coupler Latch Lock Set - Swivel Design - 2" Hitches
- Search Results: 7 way to 4 way
- Search Results: 2 conductor wire
- Q&A: Shank Length of Curt C45311 Class III Ball Mount
- Shop: TowSmart Locking Boomerang Hitch Pin and Coupler Lock - 1-1/4" and 2" Diameter
- Search Results: trailer wiring
- Shop: Brake Controller
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: How to Measure for Trailer Hitch Drop
on Trailer Hitch
Justin S.
6/4/2025
Thanks Jameson, Do you know the require length of ball mount extension needed to clear? Does it need to be 14" long like the mount you recommended?