Hitch and Trailer Wiring Recommended for 2022 Ford Escape Hybrid

Question

Question:

We have a 2022 Ford Escape hybrid that we just had an etrailer base plate installed for flat towing behind our rv. We would also like to put one of your tow hitches on the car. What wiring kit would we use in the rear of the car that would just plug in? We have had diodes put in for the blinkers

asked by: Bruce A

0

Expert Reply:

Hi Bruce, I'd be happy to help you with that!
For a trailer hitch, I'd go with the etrailer brand # e89YR. For a trailer wiring harness, I like the Tekonsha # TE54FR. The wiring harness is a plug and play install, but you will need to run a 12V feed to the Escape's start battery using the included wire and hardware.

expert reply by: Mike L

0

Mike L.

9/12/2025

Hey Bruce, did you get a chance to install the Tekonsha wiring harness and run the 12V feed to your Escape's start battery? I'm asking because your experience could help others looking to set up their vehicles for towing.

Bruce A.

9/12/2025

@MikeL Hello Mike, Yes I did install the harness and run the power from the battery! It is a hybrid, and the battery is in the back of the car , and made it very easy! Bruce

Mike L.

9/17/2025

@BruceA Good deal, congratulations on your successful install!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Hitch and Trailer Wiring Recommended for 2022 Ford Escape Hybrid

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching