Looking for a 7 Way, Brake Controller, and Weight Distribution for My 2024 Toyota Sienna?

Question

Question:

Sir, My daughter has a 2024 Toyota Sienna Woodland with factory towing package and I would like to be able to tow a T@B 400 trailer. She needs to get a 7-pin connector installed but I am wondering which electric braking she needs and what weight distribution hitch she might need? Does she need a weight distribution hitch? Thanks!

asked by: Timothy H

0

Expert Reply:

Hello Tim,

Since your daughter’s 2024 Toyota Sienna came equipped with only a 4-flat trailer connector, she’ll need a kit that we assemble in-house to upgrade to a 7-way. I recommend the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7. This kit will require running a power line from the battery, installing a few circuit breakers, and routing a brake wire from the front to the rear of the vehicle. I’ve attached an installation video that walks through the process step by step.

For the brake controller, I suggest the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional # RED52VR. The Sienna doesn’t have a factory plug-in for a vehicle-specific pigtail, so the wiring will need to be spliced in manually. While I don’t have an install video specifically for the Sienna, the attached video (on an FJ Cruiser) shows a similar install. If you skip ahead to around 13:15, you’ll see the brake controller portion.

Regarding a weight distribution system, it’s not strictly required, but it will improve the towing experience—especially for stability and comfort. Based on the specs I found for the T@B 400 trailer, which lists a GAWR of 3,900 pounds, you’ll want to ensure the tongue weight is in the 10–15% range of the total loaded weight. A great option is the Blue Ox SwayPro Weight Distribution w/ Sway Control for 2" Hitch - 5.5K GTW, 550 lbs TW # BXW0550.

Will you be doing the install for her?

expert reply by: Kate F

0

Kate F.

9/12/2025

Hey Tim, did you decide to go with the brake controller and weight distribution system I recommended for your daughter's Sienna? I'm curious to know how the installation went and if it improved the towing experience, as it could help others in a similar situation.

Answer 1

We sure do Ahmet. For your AWD 2024 Toyota Sienna you'll need the Coil SumoSprings Custom Helper Springs item #CSS-1168R you were looking at. These have been confirmed to fit the AWD models. They will easily install in your coil springs to keep…

view full answer...

Answer 2

For your 2021 Toyota Sienna XSE Hybrid, I recommend going with the American made Curt #C22UR. Your Sienna Hybrid is rated up to 3,500 pounds towing and 350 pounds of tongue weight capacity, at least that I could find, so the Draw-Tite #DT55MR with…

view full answer...

Answer 3

I took a look online, the Curt Trailer Hitch item #C13105 you have on your Sienna is rated to be used with a weight distribution system. The best one for your 2,100 lbs pop up camper is going to be the Equal-i-zer Weight Distribution System item…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Looking for a 7 Way, Brake Controller, and Weight Distribution for My 2024 Toyota Sienna?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching