Can The Curt CrossWing Gooseneck Adapter C32DR Be Used With Offset Gooseneck Ball?

Question

Question:

Can the Curt 4 Offset Ball for Double-Lock Gooseneck Hitch Part Number: C602 Be used with Curt CrossWing Lightweight Gooseneck-to-5th-Wheel Trailer Hitch Adapter - 20,000 lbs Part Number: C32DR ?

asked by: Shayne D

0

Expert Reply:

Hello Shayne, thanks for reaching out. I checked with my contact at Curt, and they said the Curt CrossWing Lightweight Gooseneck-to-5th-Wheel Trailer Hitch Adapter # C32DR should only be used with standard gooseneck balls, and should not be used with an offset ball. The CrossWing hitch provides 5" of offset, so you would not want to add more offset to this setup.

expert reply by: Jesse M

0

Curt CrossWing Lightweight Gooseneck-to-5th-Wheel Trailer Hitch Adapter
(click to enlarge)

Jesse M.

9/12/2025

Hey Shayne, did you find a standard gooseneck ball to use with your Curt CrossWing hitch? If you're still looking for a solution, I'm happy to help.

Answer 1

What you can do is attach the power wire for the backup camera #HM50002 to the running light circuit so that you won't have to run any wires or install a switch. Then to operate the camera you would just turn on the running lights. Now, this…

view full answer...

Answer 2

For your LED Marker Light RV Side Cameras w/ Night Vision for Furrion Vision S Systems #FOS05TASF you will want to follow the wiring as provided below: RED: Connects to positive wire on running lights circuit. BROWN: Will connect to the positive wire…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Kent! Your Alliance Avenue already has some great suspension components with the MORryde CRE3000 equalizers, wet bolt kit, and Rota-Flex pin box. I wouldn't replace any of those unless you're experiencing a specific problem. The next…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Can The Curt CrossWing Gooseneck Adapter C32DR Be Used With Offset Gooseneck Ball?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching