Troubleshooting Curt Hitch Mounting Bracket Not Lining Up on a 2025 Toyota Sienna
Updated 09/29/2025 | Published 05/06/2025 >
Question:
I installed my new trailer mount on my 2025 Toyota sienna and on one side my bolt plate is bent just enough that I can not bolt in all six bolts. I have a picture if you need it for visual representation. I am concerned that the tow weight and safety of the hitch is compromised by being supported by only 5 bolts.
asked by: Adam B
Expert Reply:
Hey Adam, thanks for reaching out!
I totally get where you're coming from, and I'm glad you're concerned about safety. Feel free to shoot any photos over to my email address ([email protected]) and I'd be happy to take a look at them for you, but I will say that the mounting brackets on hitches, like your Curt # C22UR, being bent isn't always something to be concerned about.
Shipping agencies can be pretty rough on the packaging and so it's not uncommon for those brackets to be slightly bent during shipment. As long as there isn't any cracking or parts that look too seriously bent, you can slowly push the bracket back into place to get that last hole to line up.
We actually have a help article on how to do this, it happens that often.
Hopefully this helps put your mind at ease, but feel free to reach out in the comments below and/or with a photo in the email provided above and I'd love to help make sure you're confident in the hitch installation!
What do you plan on using the hitch for?
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Setting Up Your Curt T-Connector Vehicle Wiring Harness - 2026 Toyota Sienna
- Q&A: What is the Best Hitch for a 2026 Toyota Sienna?
- Shop: Trailer Hitch
- Shop: Coil SumoSprings Custom Helper Springs for Coil Spring Suspension - Rear Axle
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: hitch rise
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Curt Powered Tail Light Converter Installation - 2022 Toyota Sienna
- Video: Installing the SumoSprings Custom Helper Springs on a 2025 Toyota Sienna
- Shop: Suspension Enhancement
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Old Man Emu Custom Coil Springs - Rear - Qty 2
- Shop: Curt Mounting Bracket for 4-Pole Flat Trailer Connector
- Q&A: Do You Have Coil SumoSprings for a AWD 2024 Toyota Sienna?
- Shop: Firestone Coil-Rite Air Helper Springs - Rear Axle
- Q&A: Comparing Curt and etrailer Hitch for 2023 Toyota Sienna
- Video: Curt Class III Trailer Hitch Installation Guide - 2023 Toyota Sienna
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review





Jon G.
9/29/2025
Hey Adam, did you have a chance to check if the bracket could be adjusted to fit all six bolts? I'm asking because your experience could help others who might face a similar issue with their hitch installation.