USA Made Bearing Kit that Fits 7k Axle of 2019 Grand Design 351M

Question

Question:

Hello! I have 2019 grand design 351m with 2 easy lube 7000 lbs axle. I would like the USA made timken bearing kits for the wheels. Can you help? Thanks!

asked by: Timothy J

0

Expert Reply:

Hey Timothy, yes the Timken Bearing Kit part # TMK92VR is correct USA made bearing kit for a trailer with 7k axles like your 2019 Grand Design 351M.

expert reply by: Jameson C

0

Timothy

3/28/2025

Thank you, I will order but it may be a few weeks before I can schedule with mechanic, will that be ok just I case there is a problem? Thanks!

Jameson C.

3/31/2025

@Timothy Problem with what? Delaying ordering won't be a problem on our end at all.

Timothy J.

4/13/2025

@JamesonC another question my axles are 7000 lbs, 3500 each side but in one of your reply you said this is. It for 3500 lbs axles? I thought 7000lbs axles are 3500 each wheel? Confused thanks

Jameson C.

4/14/2025

@TimothyJ The bearing kit above is for sure for 7k axles.

Answer 1

Hey Hoss, do you happen to know the axle capacities on your trailer? I'd imagine what you have is either a 6k or 7k axle setup but it's always a good idea to verify. If you do have a 6k axle the correct bearing kit would be the part #BK3-210…

view full answer...

Answer 2

Hi David! From what I could find about your 2024 Brinkley 3110, the 7k axle you have is a Lippert. This does make thing easier as they tend to use the 14125A and 25580 bearing combination for this axle. However, I am always a little nervous about…

view full answer...

Answer 3

Hello George. We will undoubtedly have a bearing kit for the 7K Lippert your 2017 Jayco North Point 5th wheel. That said, I do not have a way to tell you the exact seal size based on the info you provided. The best way to find this out will be to…

view full answer...

Answer 4

If you remove the hub and wipe away the grease on the spindle you can check to see if it is damaged. Look for an scarring, gouges, discoloration, or scoring on the spindle. If the spindle is damaged then the bearings won't ride properly and can…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

USA Made Bearing Kit that Fits 7k Axle of 2019 Grand Design 351M

Product Page this Question was Asked From

Continue Researching