Replacement Prop Rod for Leer HF350M on 2014 Toyota Tundra

Question

Question:

Hello! 2014 Tundra with HF350M-what prop rod do I need?

asked by: David

0

Expert Reply:

Hey David! What size bed do you have on your 2014 Toyota Tundra? If you have the 5-1/2' bed you need the Replacement Prop Rod Assembly for Leer Tri-Fold Tonneau Covers # LE44MR. If you have the 6-1/2' bed you need the # LE94MR.

expert reply by: Robin H

0

Replacement Prop Rod Assembly
(click to enlarge)

David

3/4/2025

I have the short bed! 5.5

Robin H.

3/4/2025

@David then the # LE44MR is the right one for you.

Robert

10/31/2025

@RobinH can you tell me the dimensions

Robin H.

11/2/2025

@Robert they don't list all of the dimensions for the prop rods. If you can tell me the year, make, model, and bed length I have a chart from Leer I can use the find the right part number for your cover. I'm assuming you have an HF350M.

Answer 1

Hey Tim! We actually have all of those parts available. You need the following: -Replacement Prop Rod Clips for Leer Tonneau Covers #LE22RR (208364) -Replacement Quick Release End for Leer Tonneau Covers #LE52GR (139514) x2 -Replacement Snap-On Ball…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Prop Rod for Leer HF350M on 2014 Toyota Tundra

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching