How Far Apart are the Holes of the Roadmaster Spacer Block part # RM-222-20

Question

Question:

How far apart are the holes?

asked by: Josh

0

Expert Reply:

Hey Josh, the holes of the Roadmaster Spacer Block part # RM-222-20 are separated by 1-1/2 inch on center.

expert reply by: Jameson C

0

Jameson C.

11/3/2025

Hey Josh, did that 1-1/2 inch hole spacing on the Roadmaster spacer block line up the way you needed? Knowing how it fit could help others working with the same quick disconnect kit.

Answer 1

Hey there Ray; yes you can mix a cargo box and a bike rack on the Benton cargo rack system for 2" hitches #B42FR. This setup has a lot of versatility with 2 pairs of crossbars to support full-size accessories like cargo boxes, bike trays, and…

view full answer...

Answer 2

The Shim for Narrow Bracket Strap Hinge #PLR2001-SS measures 4-1/2" long and 1-1/4" wide. The distance between the mounting holes is 3-1/4". The diameter of the holes is 7/16". I have attached a diagram below for your reference.

view full answer...

Answer 3

Hi Kris; thanks to all of the information you provided I think I know exactly what you need. I recommend the Benton ShellRaiser Roof Cargo Box #B44FR. This has 8 cubic feet of storage and fits crossbar spreads from 13-3/8" - 29". It…

view full answer...

Answer 4

We do indeed offer two sizes of replacement end caps for Yakima round crossbars. We offer the smaller diameter #Y80159 that you referenced, and the larger diameter also in a set of four pieces as part #Y8007026. These larger diameter end caps fit all…

view full answer...

Answer 5

It sounds like you have the round Yakima crossbars on your Jeep Wrangler Unlimited and you're looking for the EndCap #Y8790009 replacement part. This number is for a single unit but if you're wanting more than one (for some spares) you can…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

How Far Apart are the Holes of the Roadmaster Spacer Block part # RM-222-20

Product Page this Question was Asked From

Continue Researching