What is Width of Vertical Bracket of Blue Ox SwayPro Weight Distribution Shank

Question

Question:

would like to know the width of the vertical section with the holes in it. The width on the non hole side of the if that makes sense

asked by: Mike

0

Expert Reply:

Hey Mike, the width of the vertical portion of the Blue Ox SwayPro weight distribution shank part # BXW4003 that you referenced is 2 inches. This shank like nearly all WD shanks on the market is made to the industry standard for WD shanks so it can be used with nearly all other brands on the market.

expert reply by: Jameson C

0

Mike

1/15/2025

Thanks Jameson, I am assuming that it is a 2" square piece? did you by chance measure the hole side as well? ThankMike

Jameson C.

1/15/2025

@Mike Yes it is 2 inch square. Basically the whole shank uses 2 inch by 2 inch steel aside from the gusset obviously.

Mike

1/15/2025

Thanks again Jameson, Final question I just checked my new truck and it has with a 2.5" receiver who would have thought, looking for this same drop only to fit a 2.5" not 2" prefer to not use a 2.5x2 reducer. what would you recommend.

Jameson C.

1/15/2025

@Mike We have the Bulletproof Hitches shank part # BPH75RR that has the same specs except is for a 2.5 inch hitch.

See All (5) Replies to Mike ∨

Answer 1

It sounds like what you are saying is that when you upgraded to the bigger 2019 Ram 2500 that your receiver was too high on the taller truck and now when you connect to your 2018 Keystone Cougar Trailer the coupler is too low. It sounds like you need…

view full answer...

Answer 2

To lock the BulletProof Hitches 2-Ball Mount for 2-1/2" Hitch #HD254 to your hitch receiver I recommend the InfiniteRule Hitch Lock #34061072-D, but if you're interested in locking the platform to the ball mount as well then you'll want…

view full answer...

Answer 3

The spring bars may or may not play a part. Given the trailer is from 2020, there is a good chance you have spring bars that work with the old or new head. The old head is the Replacement Head for Blue Ox SwayPro Weight Distribution Systems #BXW4011…

view full answer...

Answer 4

To answer your question first- Yes. You are able to use the Blue Ox Sway Pro Weight Distribution Shank #BXW4003 as a standard rise/drop ball mount. To make it a complete towing setup, you need to add the Ball Mount Adapter #BA-1 , which works with…

view full answer...

Answer 5

Determining the correct rise or drop for your Blue Ox SwayPro Weight Distribution System #BXW1000 is going to be the same method as determining rise or drop for a standard ball mount. You will just need to measure from the ground to the top of your…

view full answer...

Answer 6

To use the Blue Ox SwayPro Weight Distribution w/ Sway Control #BXW1000 with a vehicle that has a different height, you don't need to replace the entire system, you just may need a longer shank for increased rise or drop. I recommend using the…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What is Width of Vertical Bracket of Blue Ox SwayPro Weight Distribution Shank

Product Page this Question was Asked From

Continue Researching