Can Lippert Ground Control 3.0 System Have Rear Jacks Mounted at Different Distance from Front Jacks
Published 01/15/2025
Question:
So to make sure I understand, Lippert said it would be acceptable for one rear jack to be 1.5 inches closer to the axle than the other if there are clearance issues? I also read in another question that the rear jacks could be installed on the inside of the frame rail if needed? I'm having trouble with locating my rear jacks for installation, thanks.
asked by: Steve S
Expert Reply:
Hey Steve, yes that is correct it is okay to have a slight difference in position of the rear jacks if needed due to clearance issues when installing the Lippert Ground Control part # LC358590.
It is highly recommended to install the rear jacks on the outside of the frame but if absolutely needed you can mount them on the inside of the frame. With that in mind do you think you'll be able to get the jacks mounted?
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Bluetooth Control - 6-Point Set
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Search Results: lippert camper jacks
- Video: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System Installation - 2020 Forest River Ch
- Video: How to Install the Lippert Ground Control 5th Wheel RV Leveling System - 2015 Forest River Vengeance
- Shop: Circuit Breaker - 50 Amp - Perpendicular Mount Bracket - Cycling Auto Reset - Plastic - Type I
- Shop: Derale Automatic Resetting Circuit Breaker - 50 Amp
- Search Results: 50 amp breaker
- Search Results: 50 amp fuse
- Q&A: 6 Point Automatic Leveling System Recommendation 2010 Keystone Montana Fifth Wheel
- Q&A: Mounting Plate Height of Replacement I-Beam Jack Bracket for Lippert Ground Control
- Q&A: How Much Room on RV Frame Does Lippert Ground Control Middle and Rear Jacks Take Up
- Q&A: How to Determine if Lippert Ground Control 3.0 Will Fit 5th Wheel RV
- Q&A: Solutions To Add More Clearance For Lippert Ground Control 3.0 Jack Legs
- Q&A: Can Rear Jacks of Lippert Ground Control be 24 inches From Rear Axle
- Q&A: Installation Of The Lippert Ground Control 3.0 Jack Leg Mounting Brackets
- Article: Trailer Wiring Diagrams
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Search Results: trailer jack
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Article: 5 Things to Know About Weight Distribution Hitches
- Search Results: trailer wiring
Steve S.
1/15/2025
Yes, I should be able to mount then in the outside of the frame with the small offset. Thank you for your help.