Can Rear Jacks of Lippert Ground Control be 24 inches From Rear Axle

Question

Question:

when mounting a 6 point 3.0 leveling system can the center jack be more than 12 from tire my rear jack jack will be mounted approximately 24 from landing gear

asked by: Jack C

0

Expert Reply:

Yes having the rear jacks of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote # LC675817 24 inches from the rear axle would be totally fine.

expert reply by: Jameson C

0

Answer 1

The middle and rear jack mounting brackets of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 that you referenced are a total of 6 inches in width. That's how much free room…

view full answer...

Answer 2

I don't know what type of brackets were used on your 2022 Heartland RV Torque 5th Wheel but we carry the #LC349975, which can really only be installed at one height since they have lip that butts up against the bottom of the I-Beam. If clearance…

view full answer...

Answer 3

The mounting brackets for the rear legs of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC675817 are designed for I-Beam frames but I had mentioned before that others will a box frame have had the system…

view full answer...

Answer 4

Yes, the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC675817 which uses 6 points for leveling would fit and work well on your 2010 Keystone Montana fifth wheel. This would be an excellent way to keep your…

view full answer...

Answer 5

Thanks for the pictures of your setup as that makes it easier to understand what is going on. So all of those wiring harnesses and wire looms can be moved as long as there's enough slack in them to get them out of the way so that you could…

view full answer...

Answer 6

Our Part #LC675817 is the 6-point Lippert Ground Control 3.0 System. Lippert uses 675817 which is the exact same system we carry except we add the "LC" to the part number.

view full answer...

Answer 7

There's some wiggle room with where the jacks of the Lippert Ground Control part #LC675817 can install. I attached a page I took from the install instructions that shows the more specific way to know where you can mount the jack legs.

view full answer...

Answer 8

On most trailers there is not going to be space for two sets of landing gear legs on each side of the trailer so I would have to say no unless a professional fabricator made extensive modifications to the trailer. The issue you described with your…

view full answer...

Answer 9

The length of your 5th wheel could dictate whether you can use the 4, or need to go with the 6 jack unit. Use the #LC358590 4 jack system if there will be 20' or less between the center of the landing gear footpad and the center of the rear jack…

view full answer...

Answer 10

I spoke with a representative of Lippert concerning the installation of the middle jacks on your Lippert Ground Control 3.0 - 6-Point Set #LC675817 and was told that there is not a set distance. What you will need to do is run a string line like in…

view full answer...

Answer 11

We've spoken with Lippert in the past about alternate mounting locations for the rear jacks if there is anything that would interfere with the recommended dimension. Here's what they told us as far as where you can mount the jacks on the…

view full answer...

Answer 12

The 6-Point Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC675817 will work on your trailer with a GVWR of 16,700 lbs, so long as you are sure you will not exceed the 15,500 lb capacity of the system. If you are over that weight…

view full answer...

Can Rear Jacks of Lippert Ground Control be 24 inches From Rear Axle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching