Mounting Plate Height of Replacement I-Beam Jack Bracket for Lippert Ground Control
Updated 12/18/2020 | Published 11/14/2019
Products Featured in This Question
Question:
What is the dimensions of a Replacement I-Beam Jack Bracket # LC349975? I found where you supplied partial dimensions but it doesnt include the main plate height.
asked by: Mike S
0
Expert Reply:
The overall height of the mounting plate of the Replacement I-Beam Jack Bracket for Lippert Ground Control # LC349975 is 13 inches.
expert reply by:
Jameson C
0
click to enlarge
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: lippert camper jacks
- Shop: Derale Automatic Resetting Circuit Breaker - 50 Amp
- Shop: Circuit Breaker - 50 Amp - Perpendicular Mount Bracket - Cycling Auto Reset - Plastic - Type I
- Search Results: 50 amp breaker
- Search Results: 50 amp fuse
- Q&A: Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 Leveling Systems
- Video: Ultimate Overview of the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0
- Shop: Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0
- Q&A: Is There A Leveling System Capable Of Working On a 36' 5TH Wheel With 6" Tall Frame?
- Video: Let’s Check Out the Ultra-Fab Gooseneck Trailer Tripod Stabilizer
- Search Results: 5th wheel tripod
- Shop: Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1
- Shop: Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black
- Shop: Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System
- Shop: Ultra-Fab Gooseneck Trailer Tripod Stabilizer - Steel - 31" to 54" - 5,000 lbs
- Article: Gooseneck to 5th Wheel Adapters
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: RV Camera
- Q&A: Replacement Jack Motor For The Lippert Ground Control 3.0 4 Point System
- Q&A: Dimensions of Weld Tabs and Diameter of Lippert Ground Control Leg # LC362485
- Q&A: Replacement Lead Leg For The Lippert Ground Control 3.0 On A 2021 Grand Design 3030RLS
- Q&A: Recommended Lift Kit for a 2019 Keystone Cougar 29RKS
- Q&A: Upgraded Suspension Components for 2016 Jayco Pinnacle 38 FLSA
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: Gooseneck Trailer Hitch Information and Review
- Article: 5th Wheel to Gooseneck Adapters
- Article: Ram Trailer Tow Prep Package
Marc H.
4/18/2020
When installing the LC349975 rear bracket, should I drill through all of the 4 predrilled holes on the bottom horizontal plate of the bracket into the horizontal bottom steel part of the 10 inch frame I-beam? This would result in drilling two holes into each side of the flat horizontal part of the I-beam for a total of 4 drilled holes. Is this the correct installation for the lower portion of this bracket to the trailer frame I-beam in order to assure that the rear jack leg when retracted will stay vertical? Thanks for a reply.