Can the Rear Jacks On the Lippert Ground Control Be Installed With More Than 7" Clearance

Question

Question:

Can I install jacks LCI 3.0 System more than 7” high to gain clearance?

asked by: Dan

0

Expert Reply:

Yes, you can install the rear jacks on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC675817 so that there is more than 7" of ground clearance. That said, any additional ground
clearance added to the jack location will decrease the amount of level correction available to the system.

expert reply by: Conner L

0

Answer 1

Yes having the rear jacks of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC675817 24 inches from the rear axle would be totally fine.

view full answer...

Answer 2

Yes, the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC675817 which uses 6 points for leveling would fit and work well on your 2010 Keystone Montana fifth wheel. This would be an excellent way to keep your…

view full answer...

Answer 3

The mounting brackets for the rear legs of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote #LC675817 are designed for I-Beam frames but I had mentioned before that others will a box frame have had the system…

view full answer...

Answer 4

The middle and rear jack mounting brackets of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 that you referenced are a total of 6 inches in width. That's how much free room…

view full answer...

Answer 5

I don't know what type of brackets were used on your 2022 Heartland RV Torque 5th Wheel but we carry the #LC349975, which can really only be installed at one height since they have lip that butts up against the bottom of the I-Beam. If clearance…

view full answer...

Answer 6

There's some wiggle room with where the jacks of the Lippert Ground Control part #LC675817 can install. I attached a page I took from the install instructions that shows the more specific way to know where you can mount the jack legs.

view full answer...

Answer 7

Thanks for the pictures of your setup as that makes it easier to understand what is going on. So all of those wiring harnesses and wire looms can be moved as long as there's enough slack in them to get them out of the way so that you could…

view full answer...

Answer 8

We've had this question before and when I spoke to Lippert about this scenario they responded with saying that the mounting brackets are designed to go behind and under the cross shaft of the slide out. If you check out the picture I attached…

view full answer...

Answer 9

On most trailers there is not going to be space for two sets of landing gear legs on each side of the trailer so I would have to say no unless a professional fabricator made extensive modifications to the trailer. The issue you described with your…

view full answer...

Answer 10

In regards to the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817, the middle and rear jacks require at least 6" of space on the frame for mounting. If you don't have this much space then I can see trimming…

view full answer...

Answer 11

We've spoken with Lippert in the past about alternate mounting locations for the rear jacks if there is anything that would interfere with the recommended dimension. Here's what they told us as far as where you can mount the jacks on the…

view full answer...

Answer 12

Our Part #LC675817 is the 6-point Lippert Ground Control 3.0 System. Lippert uses 675817 which is the exact same system we carry except we add the "LC" to the part number.

view full answer...

Can the Rear Jacks On the Lippert Ground Control Be Installed With More Than 7" Clearance

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching