Replacement Bushings and Bushing Sleeves for Roadmaster End Link Kit 590170-00

Question

Question:

P/n RM 590170-00 What is the part number to replace bushings and sleeve for the end links. Just bought the complete kit back in Sept. sway bar and end links and passenger side bushings are already wore out . Also, is there a warranty on these. Thanks

asked by: Joe

0

Expert Reply:

Hey Joe, thanks for reaching out!

To replace the bushings and sleeves for the End Link Kit for Roadmaster Rear Anti-Sway Bar # RM-590170-00 you need the following:

- Bushing # RM74ZR (Need 4)
- Bushing # RM-205223-00 (Need 4)
- Bushing Sleeve # RM38DQ (Need 2)
- Bushing Sleeve # RM52EQ (Need 2)

The End Link kit has a limited lifetime warranty as does the Rear Anti-Sway Bar # RM-1139-173-00 you purchased. If you believe this is a warranty situation then you'll want to reach out to Roadmaster directly at this link (https://warranty.roadmasterinc.com/) as they prefer to handle warranty directly.

Do you use your truck as a daily driver/towing vehicle, or have these all worn down from intermittent use?

expert reply by: Jon G

0

Joe

1/10/2025

Intermittent use. I use the truck to haul my cab over camper

Jon G.

1/10/2025

@Joe Do you have any suspension enhancement on your truck? I'm wondering if the in-bed camper is adding extra wear to the anti-sway and is causing premature wear?

Answer 1

Hey Craig, it looks like the correct SumoSprings kit part is #SSR-128-40-2 for your 2025 Ford F-350 Tremor 4x4 but I do need you to check one thing to be totally sure. Go check out the leaf springs on the back of your truck. Make sure there isn't…

view full answer...

Answer 2

Hey Bob, congrats on a setting up a new camper! Out of all of those options you'll also need to consider daily driving comfort unless that camper is a permanent addition to your truck bed. Listed below are a brief breakdown of each and a…

view full answer...

Answer 3

Hey Cory, Air springs are going to be the best at leveling your F-350 back out once the weight is added but they will most likely affect your unloaded ride quality, even when aired down. That being said, a majority of the unloaded ride quality…

view full answer...

Answer 4

Hey Jay, the SuperSprings kit part #SS94VR that you referenced will fit your 2017 Ford F-250 that has the SumoSprings Rebel part #SSR-128-47-2 installed already. The two kits would not interfere with each other.

view full answer...

Answer 5

Hey Art! Definitely sounds like you've got quite a bit of weight on the rear end of your F-350. I have a couple of options for you but I'll need you to verify something for me before ordering. If your truck has a bump stop perch over the axle…

view full answer...

Answer 6

Hey Michel! I also really like SumoSprings since they're easy to install, don't require maintenance, and don't ruin unloaded ride quality like some other options do. You can go with the traditional style like #SSR-127-54 as long as you…

view full answer...

Answer 7

Hey Peter, thanks for the pictures of your leaf springs loaded and unloaded. I don't think we've ever had anyone send us pictures for that before so that is interesting to see. That's quite a bit of sag and it looks like your overload…

view full answer...

Answer 8

Hey Joe! You'll want the Replacement Bushing Sleeve item #RM-205501-00 for the Roadmaster Rear Anti-Sway Bar item #RM-590170-00. These are sold individually. Additionally, you'll want to pick up a couple of the Replacement Polyurethane Hat…

view full answer...

Answer 9

I will start off by saying that the Replacement Bushing #RM-205381-00 is the direct replacement for the Roadmaster Polyurethane Bushing Kit for 1-3/8" Diameter, Factory Rear Anti-Sway #RM-4139-300. To further that, the Replacement Polyurethane…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Replacement Bushings and Bushing Sleeves for Roadmaster End Link Kit 590170-00

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching