Availability of Installation Video and Description of Air Lift Air Bags on 2023 Nissan Frontier

Question

Question:

I have a Nissan Frontier 2023 PRO 4 X and I would like to know if there are any videos available and the product description.

asked by: George

0

Expert Reply:

Hi George; the only video we have for the Air Lift LoadLifter 5000 # AL39DQ is the breakdown attached below. We won't have an installation video for a 2023 Frontier until someone brings one for us to install the air bags.

These have a load-leveling capacity of 5,000 lbs, lifetime warranty, and are made in the USA. They are constructed of 2-ply, fabric-reinforced rubber and have Zytel nylon endcaps to keep them secure. The air bags will help keep you level while reducing the strain on your suspension. They can also be run at the minimum 5 psi so they won't impact unloaded ride quality.

The full description can be found on the product page. Normally the installation instructions would be attached at the bottom of this page but it looks like they're missing right now. You can find them here if you want to check them out:

https://digital.airliftcompany.com/m/2c0bde5c2f4d00de/original/MN-1185.pdf?_ics=1734697070165&irclickid=~5WMFywCBuqnsuxCuwxEKBrszqwzArilig~145VWOGEuqgdc~4XUK

expert reply by: Robin H

0

Robin H.

11/17/2025

Hey George, were you able to check out the breakdown video and the installation instructions for the Air Lift LoadLifter 5000 on your Frontier? Knowing how that info worked for you could help others waiting on a video for newer models. Your update could make it easier for the next person with the same setup.

Answer 1

Hey Rob, thanks for reaching out! The unibody definitely can be a problem, especially when the owner's manual discourages it. I get the concept behind the Anderson WD hitch, but frankly I'm a little skeptical of it myself, so I have some…

view full answer...

Answer 2

That is correct, the SumoSprings Solo Custom Helper Springs #SS46EV will replace the factory bump stop on your 2022 Nissan Frontier. Installation requires the removal of the factory bump stop and frame mounted cup. Once this is done you will thread…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability of Installation Video and Description of Air Lift Air Bags on 2023 Nissan Frontier

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching