What Size Nut Does Replacement Cap Wrench for TST SE2 Cap Sensors Fit

Question

Question:

Hi... Im looking at the TPMS wrenches and need a spare. Can I assume they are the same size? I think mine are 12mm but maybe could be 13mm? Are the TPMS locking bolts all the same size? Thanks

asked by: David H

0

Expert Reply:

Hey David,

The Replacement Cap Wrench for TST SE2 Cap Sensors # TST89FR works with 1/2" nuts that come with the TST brand TPMS which is around that 12mm/13mm size.

expert reply by: Jon G

0

David H.

12/2/2024

Thank you Sir! We find that we need more than one wrench. In just checking the truck tires we realized the wrench is over at the trailer. So, in total truth, we need three - two including the original - one for the tool box, one for the truck and one for the RV. Trying to get those thin bolts off with a standard open end wrench isn't as easy as it looks. David

Jon G.

12/2/2024

@DavidH Good thinking! We love to hear how everyone uses the parts we sell!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

What Size Nut Does Replacement Cap Wrench for TST SE2 Cap Sensors Fit

Product Page this Question was Asked From

Continue Researching