Availability of Custom Wiring Harness for 2021 Chevrolet Bolt EV

Question

Question:

Good morning. Im trying to find out if a trailer light T-connector to be installed on my 2021 Chevrolet Bolt EV, is something that does exist and is available? The lights on my trailer are all LEDs. Thanks for your help. Pierre

asked by: Pierre

1

Helpful Expert Reply:

Hi Pierre; there are no custom wiring harnesses with a T-connector for your 2021 Chevy Bolt EV but you can use the # 119147KIT. This will still give you a 4-way connector at the rear to power your trailer's signal lights. If you're worried about splicing, the ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT is another option. This clamps onto the wiring making it popular for electric vehicles like yours.

expert reply by: Robin H

1

Robin H.

12/15/2025

Hey Pierre, how did things go with the wiring harness for your Chevy Bolt EV? Did the option you chose power your trailer’s LED lights the way you needed? Your update could make it easier for others with the same vehicle setup.

Pierre

12/15/2025

@RobinH To be honest, I was in hospital for a surgery about replacement of my aorta valve with a mechanical one and a couple of bypass. Iv'e been quiet for almost a full year, but since the end of October 2025 I feel a hole bunch better and I will surely look at it after Holydays I keep walking and exercising at the gym and it does wonders. At 80 years old you dont want to shut any door. Thanks for the follow up Robin and have a Merry Christmas. Pierre

Robin H.

12/16/2025

@Pierre glad to hear you're feeling better! Merry Christmas to you as well.

Answer 1

I can certainly point you in the right direction. We do have the #e22YR which is a 26" long 2,000 lb leaf spring. We also have the #e44SR which is a 25-1/4" long 2,500 lb spring. When replacing old leaf springs, it is critical that the…

view full answer...

Answer 2

The Tru Ryde grease seals you mentioned, part #RG06-70 are indeed a replacement for the 10-036-00 Dexter seals. They would work great for your application.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Availability of Custom Wiring Harness for 2021 Chevrolet Bolt EV

Continue Researching