Trailer Bearing Kit for 2021 Forest River 29VBUD Camper

Question

Question:

Looking for bearings and races for 2021 forest river 29vbud camper. Axles are 4400 lb

asked by: Alfred W

0

Expert Reply:

For a Lippert 4,400 lbs axle you will need the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles item # BK2-100. The kits for the 3,500 lbs axles fit the 4,400 lbs.

expert reply by: Jameson C

0

Jameson C.

12/15/2025

Hey, how did the hub bearing kit work out for your 4,400 lb Lippert axle on the Forest River camper? Knowing what fit best could help others with the same setup.

Answer 1

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 2

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 or just the Grease Seal part #RG06-050.

view full answer...

Answer 3

Hey Rob; thanks for the photos and it was actually the one with the hub number that did it. That's a BD 545 which is an AxleTek 3,500 lb hub and drum like the Trailer Hub and Drum Assembly #AKHD-545-35-K. The 35 on the axle sticker was a good…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Trailer Bearing Kit for 2021 Forest River 29VBUD Camper

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching