Recommended 7-Way to 4-Way Adapter for a Stealth Hitch

Question

Question:

I purchased a stealth hitch for a 2021 Hyundai Palisade and lost the 7 pole to 4 pole adaptor. Is this the right one for a replacement? Code: 337TC2074P Thanks

asked by: Mark S

0

Expert Reply:

Yes, it is Mark! The Buyers Products 7-Way RV to 4-Way Flat Plastic Trailer Connector Adapter item # 337TC2074P is exactly what you need.

expert reply by: Jerred H

0

Answer 1

What you have there on your 1998 Ford F-150 is a 7-Way blade style connector, not a round pin connector. So for an adapter to use trailers that have 4-Way flat connectors I recommend #PK12716. I have linked a video review of this adapter for you.

view full answer...

Answer 2

When it comes to having a 7 way plug and a 4 flat plug on your 2013 Honda Pilot without splicing wires we have a bunch of adapters they can plug into the 7 way to make it a 4 flat We have The T-One Vehicle Wiring Harness for Factory Tow Package -…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Recommended 7-Way to 4-Way Adapter for a Stealth Hitch

Product Page this Question was Asked From

Continue Researching