Is the Mount-n-Lock AddaBumper Extension Plates # MO24VR a Set of Two

Question

Question:

Do you need one set for each side of the frame or just one plate per side? MO24VR Can these be used along with MO84VR which doesnt show up on your site but Id mentioned often?

asked by: Robert G

0

Expert Reply:

Hey Robert, the Mount-n-Lock AddaBumper Extension Plates # MO24VR comes with two plates and all that's needed. We do not carry the drop plates MO84VR currently.

expert reply by: Jameson C

0

Robert G.

9/23/2024

Is the MO84VR drop plate just out of stock or has it been discontinued?

Jameson C.

9/23/2024

@RobertG Looks like it's been discontinued since 2022.

Answer 1

I do say those welds are bad and it appears the bumper is simply welded onto the back plate of the trailer rather than the frame. I recommend removing the entire bumper for the Mount-n-Lock Heavy-Haul'r Replacement RV Bumper #MNT43VR which you…

view full answer...

Answer 2

I do have an option for you but we don't offer any extenders for the 24x60 etrailer Cargo Carrier for RV Bumper part #e99049. If the body of the trailer extends past the frame I recommend replacing the bumper with the Mount-n-Lock…

view full answer...

Answer 3

The easiest and most cost effective way to increase ride quality on a travel trailer like the Winnebago Minnie is to upgrade to cushioned equalizers. These will provide significant increases in smoothing out the ride. I recommend the Dexter E-Z Flex…

view full answer...

Answer 4

Hi Ryan! The etrailer XHD Non-Binding Tow Bar #e94ZR won't fit the #RM-035-1 (1" thick shackle) or #RM-035 (3/4" thick shackle) as is. However, it can be modified so the two work together. Our tow bar shares the same design as the…

view full answer...

Answer 5

The extensions you have on your 2018 Keystone Hideout 308BHDS do appear to be enough to mount the Mount-n-Lock Heavy-Haul'r RV Bumper Replacement Kit #MO94VR without needing the Extension Plates #MO24VR. I would recommend having a gusset placed…

view full answer...

Answer 6

Yes, you can use Curt weight distribution shank #C17122 with your Equal-I-zer system to get the additional length needed for you to be able to lower the tailgate on your 2017 GMC Sierra 1500. The Equal-I-zer head uses 3/4 inch diameter bolts to hold…

view full answer...

Answer 7

The Mount-n-Lock Heavy-Haul'r Replacement RV Bumper #MNT78VR comes with mounting brackets but you might need the Extension Plates #MO24VR if your frame is shorter than your RV body. All of the hardware parts needed to install the bumper are…

view full answer...

Answer 8

Hey Eric, The hitch extenders that we currently offer for a 2-1/2" receiver tube opening unfortunately max out at 6,000lbs GTW and wouldn't be capable of towing the trailer. You're most likely going to need to upgrade to a TorkLift…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 11

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Is the Mount-n-Lock AddaBumper Extension Plates # MO24VR a Set of Two

Product Page this Question was Asked From

Continue Researching