Wiring Color Functions of LED Peterson Taillight # PE96CR

Question

Question:

What are the color for the wires? We all know the function, but not the wire colors.

asked by: Lief

0

Expert Reply:

Hey Leif, on the LED trailer taillight part # PE96CR the white is ground, the black is running light, red is turn signal stop, and green is reverse.

expert reply by: Jameson C

0

Jameson C.

1/27/2026

Hey Leif, did those wire color details for the LED trailer taillight match what you found on your setup? Knowing how the wiring lined up could help others working on the same light.

Answer 1

The white wire of the Peterson light part #PE46CR is the ground, black is running lights, red is stop/turn, and then green is backup.

view full answer...

Answer 2

I recommend the Optronics LED trailer light kit #TL16RK. The kit includes 2 LED tail lights, 2 amber side marker and clearance lights, license plate bracket, wiring harness and stainless steel mounting hardware. I also recommend getting a deluxe…

view full answer...

Answer 3

Both the pigtail and the trailer harness included with the Peterson #V944 LED Taillight Kit are 18 gauge, which is typical for trailer lamps and wiring harnesses. 18 gauge wire is actually perfectly sufficient for the reduced power draw of LED lamps…

view full answer...

Answer 4

We do have a couple of really good options for you to replace your Peterson ##PM444L and #PM444, but you do have a keen eye because the Tail Light Kit #TLL16RK will not work with the 2-1/4" spacing you have. One of the lights would interfere…

view full answer...

Answer 5

The Standard Trailer Light Kit with 25' Wire Harness part #TL29BK as I am sure you noticed grounds via the mounting hardware therefore there is not a singular ground wire. In order to attach this light to a wooden surface you will need to run a…

view full answer...

Answer 6

Hey Darrell, yeah the correct kit for over 80 inch wide trailers that are less than 30 feet you do need to have a coupler amber lights and reflectors up front like what comes with the part #V944 plus a set of amber clearance lights #MCL95AB which is…

view full answer...

Answer 7

You are correct. The wires on the Peterson Round Trailer Tail Light with License Plate Light, part #432000, are as follows. The brown wire is the running light circuit and the red wire is the stop and turn signal circuit. The light gets grounded…

view full answer...

Answer 8

Essentially what you said is how you run wire to the part #432400. It's a pretty strange method I will agree, but basically you just insert the wires into the holes on the back of the light assemblies and they socket grabs the wire. If you…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Wiring Color Functions of LED Peterson Taillight # PE96CR

Product Page this Question was Asked From

Continue Researching