Where Are Lippert's Hub/Drum And Brake Assemblies Manufactured

Question

Question:

Where are the Lippert brakes assemblys and hubs made?

asked by: Mark S

0

Expert Reply:

Hey Mark,

Lippert stated that the brake assemblies are made in China and their hub/drum assemblies are made in the US.

expert reply by: Kevin C

0

Jesse M.

1/27/2026

Hey Mark, did that info about where the Lippert brakes and hubs are made give you what you needed? Knowing your results could help others looking into the same parts.

Answer 1

Recommending replacement components like brake pads and a wheel cylinder for a hydraulic brake assembly without knowing who manufactured it would be very difficult. Are there any part numbers or manufacturer information on them? Without any…

view full answer...

Answer 2

Hey Mark! To replace the brakes on your Lippert 4,400 lbs axles you'll need the Lippert Electric Trailer Brakes item #LC66WD. While the 4 bolt mounting pattern is the same you don't want to put 3,500 lbs capacity brake assemblies on a 4,400…

view full answer...

Answer 3

Hey Scott! Yes, the 4.4K Lippert Electric Trailer Brakes #LC66WD are exactly what you need for the 4.4K axle on your 2021 Keystone Hideout. We actually went round and round with this issue as well so you aren't the only one. We were finally able…

view full answer...

Answer 4

Hi Nate; the backing plate is not available as a replacement part so you will need the complete brake assembly. What you have in your picture is the #LC46WD. Brakes should be replaced in pairs so for the left and right hand brake assemblies you would…

view full answer...

Answer 5

So I just want to start with the brakes. Due to you having the 4,400LB Lippert axle you will need their Brake Kit #LC66WD for each axle. These brakes are forward self adjusting like the Dexter you were looking at. For a cushioned equalizer I prefer…

view full answer...

Answer 6

The correct replacement brake assemblies for your B44EA-22 is the part #AKEBRK-35-SA which is for a 3,500 lb axle and is self adjusting. Then for a matching hub/drum that has a 6 bolt pattern on it you'd need the #AKHD-655-35-K and you'd be…

view full answer...

Answer 7

Hey Michael, thanks for reaching out! To replace your brakes, you'll need to go with the Lippert Electric Trailer Brakes #LC66WD. We have some other brands that look like they would work, but from our experience it's a coincidence if they…

view full answer...

Answer 8

Hello Rob from the Netherlands, thanks for reaching out. We do not have a digital drawing with dimensions of the Lippert Electric Trailer Brakes #LC66WD that I can send. I can tell you that these brakes are basically identical to the 3,500 lb brakes.…

view full answer...

Answer 9

The Lippert Electric Trailer Brake Kit #LC66WD mounts to a brake flange 2-7/8" on center vertically and horizontally.

view full answer...

Answer 10

For self adjusting brake assemblies that fit a Lippert 4,400 lb trailer axle the correct kit you'd want is the part #LC66WD and you'd be set.

view full answer...

Answer 11

Hey Mark, thanks for all of the info you listed about your hub. With just that info we know that the hub/drum part #AKHD-655-35-EZ-K that you referenced is an exact replacement.

view full answer...

Answer 12

Hey Jason, That number shows you have a Lippert axle with a gross axle weight rating of 4,400lb so you would likely need the Lippert Electric Trailer Brakes #LC66WD. These self-adjusting brake assemblies fit 10" x 2-1/4" drums. You can…

view full answer...

Where Are Lippert's Hub/Drum And Brake Assemblies Manufactured

Product Page this Question was Asked From

Continue Researching