Best Brake Controller for a 2010 Chevy Silverado Work Truck

Question

Question:

Hello, I am new to installing a brake controller I would like advice on which controller would be best choice for my 2010 Silverado work truck.

asked by: Kenneth L

0

Expert Reply:

Hey Kenneth, thanks for reaching out!

I recommend going with the Tekonsha Primus IQ Trailer Brake Controller # TK90160 because it's entry-level as far as ease of use goes, it has a great price-point, and it's backed by a limited lifetime warranty which is pretty unusual for a controller at this price.

If your 2010 Chevy Silverado came with the factory tow package then you should just need to splice the included pigtail wiring harness to some wiring under your dash, but if you don't have the factory tow package then you'll need to also need to either connect the wiring from the Pollak Kit # PK11898 at the back of your vehicle or you'll need to connect the Hopkins # 30955 if you have a round plug instead of bare wires (at the back of your truck).

Attached is a helpful article on how to install this brake controller, as well as a few installation videos for your referenc.

expert reply by: Jon G

0

Jesse M.

1/19/2026

Hey Kenneth, how did things go with the Tekonsha Primus IQ brake controller on your Silverado? Did the wiring under the dash match up with what you found in the guide? Your update could make it easier for others setting up their first controller.

Answer 1

The 2010 Chevy Silverado will have a wire bundle tucked up under the dash, to the left of the steering column, held together with a white tag. The tag should also have the wire functions on it but we have learned that they are as follows: Red/black…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Best Brake Controller for a 2010 Chevy Silverado Work Truck

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching