Why Doesn't Brophy Replacement Wheel # 1206 Have Weight Capacity

Question

Question:

wondering what the weight capacity is on the Brophy wheel 1206 I have a cargo trailer 6 x 8 and I am looking for a rubber tire for the jack wheel.

asked by: Rich E

0

Expert Reply:

Hey Rich, the replacement Brophy wheel part # 1206 was not designed for use on a trailer so it does not have a stated weight capacity when used on a trailer. Basically it is to help move around the Brophy camper jacks part # CX74.

expert reply by: Jameson C

0

Jameson C.

1/19/2026

Hey Rich, were you able to find a rubber tire that works for your trailer jack? Knowing what you ended up using could help others looking for a similar setup.

Answer 1

It sounds like you're looking for something like the: -Replacement Wheel for Brophy Heavy-Duty Cable Camper Jacks #1206. This tire has a 1/2" diameter hole, is 1-1/2" wide, 6" in diameter, and has a rubber tire like you're…

view full answer...

Answer 2

I may have a solution for you, but we don't carry any true pneumatic wheels for swiveling trailer jacks-they're typically only going to be used on heavy duty trailer jacks and dollies like the Trailer Valet #STC-V211. With that said, you may…

view full answer...

Answer 3

The outer diameter of the pipe mount that comes with the Pro Series Round, Pipe-Mount Swivel Jack part #PS1401480303 is 2". It uses a 5/8" diameter pin.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Why Doesn't Brophy Replacement Wheel # 1206 Have Weight Capacity

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching