Recommended Replacement Trailer Jack Wheel That Has A Rubber Tire

Question

Question:

I am looking for a wheel for a front trailer jack on my 16 flat trailer, that will roll in gravel or sand. I am thinking some has to make a small rubber tire. Rather than the small hard plastic ones that are made to roll on hard surfaces like concrete?

asked by: Bob C

0

Expert Reply:

It sounds like you're looking for something like the:

-Replacement Wheel for Brophy Heavy-Duty Cable Camper Jacks # 1206.

This tire has a 1/2" diameter hole, is 1-1/2" wide, 6" in diameter, and has a rubber tire like you're looking for.

If you need anything else please feel free to let us know and we'd be happy to help.

expert reply by: Bryce D

0

Answer 1

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 2

I may have a solution for you, but we don't carry any true pneumatic wheels for swiveling trailer jacks-they're typically only going to be used on heavy duty trailer jacks and dollies like the Trailer Valet #STC-V211. With that said, you may…

view full answer...

Answer 3

Hey Rich, the replacement Brophy wheel part #1206 was not designed for use on a trailer so it does not have a stated weight capacity when used on a trailer. Basically it is to help move around the Brophy camper jacks part #CX74.

view full answer...

Answer 4

Hey Doug, I checked with Brophy and the Brophy Camper Jacks #CX74 have a distance of 3 inches from the upright mast to backside of the bracket that would hold your camper shell. We do not have a version of this without the feet.

view full answer...

Answer 5

It sure is Steve and welcome back! The etrailer Sidewind Trailer Jack w/ Drill Adapter item #e88GV is the correct jack if you don't want the SnapPad. This one is designed to fit the standard bolt pattern of an A-Frame trailer coupler and can be…

view full answer...

Answer 6

Hey Jeff! Your thinking is mostly correct. The Autowbrake Electric Brake Controller #3430001 mounts on the trailer and uses your vehicle's brake light signal from the 4-way to know when you're braking. However, it also needs a constant…

view full answer...

Answer 7

Hey Lee! The Victron parts can get pretty confusing. The Victron Orion-Tr #VN75ZR is only designed to be a power supply for DC loads, not for battery charging. You do not want to use this converter to charge any type of battery. To charge your…

view full answer...

Answer 8

Yes, technically the camper needs to hang over truck bed rails for the Brophy Heavy Duty Cable Camper Jacks - 67" Max Lift Height - 4,000 lbs #CX74 to get under the camper and lift it up properly. This should be self-explanatory, but if the…

view full answer...

Answer 9

Hello Min; the Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs #CJ74 or Brophy Heavy Duty Cable Camper Jacks - 67" Max Lift Height - 4,000 lbs #CX74 are going to be your best option. I know they only have 67" of lift but…

view full answer...

Answer 10

Hey Marcus! That's unfortunate, but yes, that is exactly where #e44QV makes sense. It replaces the drop leg inner tube on the etrailer Manual Sidewind Trailer Jacks like #e35YV, #e86AV, and #e38AV and adds the SnapPad setup at the same time. That…

view full answer...

Answer 11

Your best option for adding traction to the ramp of your toy hauler will be the Non-Slip Adhesive Safety Strips #NSAS which are 1 inch by 11 inch. You'd want to order several sets based on what the ramp would need. This would adhere do the ramp…

view full answer...

Recommended Replacement Trailer Jack Wheel That Has A Rubber Tire

Product Page this Question was Asked From

Continue Researching