Does Curt Trailer Hitch For Sure Fit 2024 Ford Ranger

Question

Question:

need to know for sure if it will 2024 ford ranger

asked by: Bryant H

0

Expert Reply:

Hi Bryant,

It's definitely a smart idea to check and make sure, and I can verify for you that yes, the Curt Trailer Hitch Receiver # C82ZV 100% will fit your 2024 Ford Ranger.

I went ahead and confirmed this fit with Curt for you as well.

expert reply by: Kyle S

0

Brian

12/19/2024

Is this a category 3 2" FRONT hitch? I have Meyers Home Snow Plow on my 2017 Tacoma but I want to get either a 2024 or 2025 Ford Ranger Lariat, keep the plow but just need the front hitch. Will this fit both 2024 and 2025 Ford Rangers?

Reply

Jesse M.

12/19/2024

@Brian Hey Brian, yes, the Curt Hitch # C82ZV is a class 3 hitch with a 2" receiver. It will fit the Ford Ranger 2024-current. This is a rear mount hitch.

Reply

Brian

12/19/2024

@JesseM also 2025 Ford Ranger and where can I get the spec to mount as I may have dealer mount it.

Reply

Brian

12/19/2024

@Brian and it is also a FRONT hitch? Photo shows the rear mount.

Reply

See All (4) Replies to Brian ∨

Answer 1

Hey Mike, the Curt hitch part #C82ZV that fits your 2024 Ford Ranger does fit pretty tight with the spare like you can see in the attached picture but the good news is that there aren't any real issues and it's not difficult to raise or lower…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey John, The common consensus on capacity is that you should really only use 80-85% to give yourself a margin or error. At 3,300lbs you'd be at roughly 94% capacity so you still technically could but it's likely going to sag the rear…

view full answer...

Answer 4

In order to make a proper selection for a hitch ball, you will need to find out what diameter size ball your trailer needs. It should be stamped on the trailer coupler or frame, either 1-7/8 or 2 inch. All bumper ball holes are 3/4 of an inch, so you…

view full answer...

Answer 5

Hey Tom! I personally like the etrailer Hitch #e37ZV because it has a matte black finish that protects the metal better than a standard glossy black finish, but I see you picked up the Draw-Tite #DT35PR which is also a great hitch that I know…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hello David, thanks for reaching out. Sounds like you are on the right track here. Both the Curt #C25FV (13568) and #C74MJ (13627) will fit all models of the 2024 CX-90 and this includes the PHEV plug-in hybrid model. This is actually a rare case…

view full answer...

Answer 8

Hey Keith, Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver #DT35PR is a confirmed fit for 2024 Ford Ranger models.

view full answer...

Answer 9

Hello Todd, I am very sorry the install is not going more smoothly for you on the Redarc #RED52VR, seems like this is an ongoing issue with the Trailblazer and finding the brake wiring. Any chance you are close to Wentzville, MO? We would love to do…

view full answer...