Redarc Brake Controller Install Harness that Fits 2024 Honda Ridgeline

Question

Question:

Is it safe to assume this adapter will also work with a 2024 Ridgeline RTL?

asked by: Brad K

0

Expert Reply:

Hey Brad, yes the Redarc brake controller install harness part # RED59FR does also fit the 2024 Honda Ridgeline RTL.

expert reply by: Jameson C

0

Jameson C.

1/19/2026

Hey Brad, how did the Redarc brake controller harness end up working with your Ridgeline RTL? Your update could make it easier for others with the same truck.

Answer 1

The Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR is a great option for maintaining a clean factory appearance inside the cab of your Honda Ridgeline (not to mention that it also works extremely well to activate the trailer brakes). The…

view full answer...

Answer 2

The brake controller I strongly recommend for your 2019 Honda Ridgeline with a factory 7-way, that does not require any type of splicing or wire cutting or other type of complicated is the Tekonsha Prodigy P3 Trailer Brake Controller #90195 with the…

view full answer...

Answer 3

For your 2023 Honda Ridgeline I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. The main unit of this brake controller will install behind the dash so only the control knob will be visible in the vehicle. This gives it a nice clean…

view full answer...

Answer 4

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 5

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Redarc Brake Controller Install Harness that Fits 2024 Honda Ridgeline

Product Page this Question was Asked From

Continue Researching