Troubleshooting Lippert Leveling Jacks Won't Stay Up

Question

Question:

Lippert leveling jacks wont stay up

asked by: Dan T

0

Expert Reply:

Hello Dan, it sounds like you are having a problem with your Lippert hydraulic leveling system. is this a new system you just installed recently? Or is this an older system that has worked before, and now it is not working? What have you tested already? Are you able to manually retract the legs? Or are they permanently stuck in the down position?

Try manually retracting the jacks and check for any fluid leaks. Try checking the wiring harness connections at both the controller and the jack, check the harness for any damage, and check the fuses at the controller, replacing anything that is damaged as necessary. If you do this or have done this and you are still having issues please let me know and I can help you troubleshoot further. Any additional information or detail you can provide will help me be more accurate with the troubleshooting.

expert reply by: Jesse M

0

Richard H.

10/10/2025

When I pick my jacks they all come up fine then one or two on passenger side will leak down 2 or 3 inches when I go back and raise them again they usely stay up

Jesse M.

10/10/2025

@RichardH Have you checked for any leaks? That is typically caused by a leak or possibly air in the lines.

Answer 1

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

Hey Julie, hopefully not but it is possible you need to replace your #LC77CJ. I would try unplugging it for 60 seconds though to see if a hard reset gets it to work like it should and go from there. Try that and let me know.

view full answer...

Answer 4

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 5

Hey Patrick, thanks for reaching out. Yes, the Replacement Front Jack Leg #LC362485 should work for your 2021 Open Range 314RLS with the Lippert Ground Control 3.0 system. Since your weld stop “bump outs” measure 17-1/2" apart, that matches the…

view full answer...

Answer 6

Hey Chris, yes the part #MC62YR does have the 50.336 motor like you are looking for.

view full answer...

Answer 7

Hey Eric, Do you only have the OneControl touchscreen inside your trailer or do you also have a separate controller on the outside or in an exterior compartment? You should have a controller that looks like either the #LC421484 or #LC74FR. If not can…

view full answer...

Answer 8

Hey Jim, thanks for reaching out! I reached out to my contact at Lippert with the info you gave me, and they said your RV came with a standard 1621 pin box, so you'll need the PullRite SuperGlide Quick Connect Capture Plate #PUL46RR for your…

view full answer...

Answer 9

Hey Marvin, The Atwood AT94022 is also unfortunately discontinued along with the rest of the Atwood brand. Water heaters have shrunk in size a bit so you're going to have to do a bit of alteration to the cutout hole to fit a new water heater.…

view full answer...

Troubleshooting Lippert Leveling Jacks Won't Stay Up

Product Page this Question was Asked From

Continue Researching