Is There Rebuild Kit for Replacement Front Jack for Lippert Ground Control 3.0

Question

Question:

Does Lippert make a rebuild kit for landing gear LC362485? Thanks

asked by: Feb_az

0

Expert Reply:

Hey Feb, no there isn't a rebuild kit for the Replacement Jack part # LC362485. If yours is damaged only solution would be a replacement

expert reply by: Jameson C

0

Jameson C.

10/22/2025

Hey Feb, were you able to find a replacement jack for your Ground Control 3.0 system? Knowing what you ended up using could help others facing the same issue.

Answer 1

Hey Patrick, thanks for reaching out. Yes, the Replacement Front Jack Leg #LC362485 should work for your 2021 Open Range 314RLS with the Lippert Ground Control 3.0 system. Since your weld stop “bump outs” measure 17-1/2" apart, that matches the…

view full answer...

Answer 2

The distance between the insides of the weld stops on the jack leg #LC362485 is 17-1/2 inches and the outer tube diameter is 2-1/2 inch by 2-1/2 inch.

view full answer...

Answer 3

It sure is Wesley. The Replacement Front Jack item #LC362485 is exact what you will need for the 6 point Lippert Ground Control 3.0 Leveling System item #LC675817. The Replacement Front Jack item #LC362485 can be used as a replacement for either the…

view full answer...

Answer 4

Hello Jerry, thanks for reaching out. I am sorry to say we do not offer a replacement rod and nut for the Lippert Ground Control 3.0 jacks. The only solution I can offer would be a whole new leg such as part #LC362485 which replaced the front jack…

view full answer...

Answer 5

For the Lippert Ground Control 3.0 system #LC358590 or #LC675817 the correct front jack replacements is the part #LC362485. This works on the front and left jacks so you'd need a quantity of two. The price is available down below at the link.…

view full answer...

Answer 6

Hey Jason, the best replacement that we have for your Norcold N1095L refrigerator is the Norcold RV Refrigerator w/ Freezer - 9.7 cu ft - 12V - Stainless Steel - Right Hand Opening Doors #NC56FR (for left hand #NC29FR ). This is a nice 12 volt…

view full answer...

Answer 7

In order to determine what system you have, you'd need to be looking at the touch pad or control module. The touch pad for the 3.0 looks like part #LC421484. There is also a part number on the control module that can be referenced but there are…

view full answer...

Answer 8

Both would actually work as a replacement front jack for your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 6-Point Set #LC675817. It just depends on if you want the jack tube only, or the jack tube, motor, and foot. -…

view full answer...

Answer 9

Hey Cecil. To replace a front jack on a Lippert Ground Control 3.0 system item #LC358590 or item #LC675817 you will need the Replacement Front Jack item #LC362485. This replacement works on both the left and right sides. What happened to your front…

view full answer...

Answer 10

No, the hall effect motor does not have to be greased, but per the service manual if the jacks are down for an extended period, it is recommended to spray the exposed leveling jack tubes with lubricant every 3 months for protection. If you live in a…

view full answer...

Answer 11

There is an easy way to tell in this situation. The Lippert Components 32" Lead 5th Wheel RV Landing Gear part #LC179013 has a weld stop measurement outside to outside of 17.5". You can simply measure yours and if it is the same these will…

view full answer...

Answer 12

We have exactly what you are looking for - heavy duty landing gear with a long extension, dual motors, and no cross member - with one set from Ultra-Fab: - Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010 This landing gear has a total capacity…

view full answer...

Is There Rebuild Kit for Replacement Front Jack for Lippert Ground Control 3.0

Product Page this Question was Asked From

Continue Researching