How to Add Brakes to Older Demco Kar Kaddy 3
Updated 07/26/2024 | Published 07/24/2024 >
Products Featured in This Question
Question:
i have a kar kaddy 3 without brakes. i wanted to see what kit or what parts individually i would need to make this work. im open but leaning towards surge brakes if possible.
asked by: Michael V
Expert Reply:
Michael, to add brakes to your Demco Kar Kaddy 3, you can use the Kodiak Disc Brake Kit # K2R35D. This will allow you to slide the rotor over the existing idler hub, and the brackets for the caliper will bolt to the brake mounting flange.
You will also need to ensure that you have this type of flange on your tow dolly otherwise you may not be able to add any brakes to the system.
You will also need the the Demco Hydraulic Brake Actuator # DM62VR as well as the Demco Hydraulic Brake Line Kit # DM5424. You will want to confirm with your tow dolly that you do have the 3" wide tongue for mounting the actuator as well as the brake flange on the hubs to be able to mount the brakes to before going to far.
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Trailer Brakes
- Disc Brakes
- Marine Grade
- 5 on 4-1/2 Inch
- Rotor
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Kodiak
more information >
Continue Researching
- Search Results: trailer brakes
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Search Results: akhd~545~35k
- Shop: Demco Replacement Shock Dampener for DA66 and DA66L Hydraulic Actuators
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Shop: Demco Hydraulic Drum Brake - Single Servo - Galvanized - 10" - RH - Self-Adjusting - 3,500 lbs
- Search Results: hydraulic brake lines
- Shop: Kodiak Hydraulic Brake Line Kit - Single Axle - 18'
- Shop: Replacement Steering Stabilizer Shock for Demco Kar Kaddy Tow Dolly - Qty 1
- Video: All About the Demco Hydraulic Brake Actuator-DM72VR
- Video: Breaking Down the Kodiak Disc Brake Kit-K2R35DKG
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Q&A: What is Standard 4 Bolt Pattern Trailer Brake Flange Dimension
- Q&A: Will Standard 3.5K Brake Assemblies Fit A Backing Plate Bolt Spacing Of 2-3/4" And 2-7/8"?
- Q&A: Replacement Drum Brakes For A Demco Kar Kaddy SS Tow Dolly
- Q&A: Recommendation for Installation of a Brake Mounting Flange on a Trailer Spindle and Axle
- Q&A: Where on the Axle Do I Install a Brake Mounting Flange?
- Video: Comprehensive Review: Brake Mounting Flange for 2-3/8" Round Axle
- Q&A: Installing Electric Brakes on a Vehicle Tow Dolly
- Shop: Vehicle Tow Bar Brake System
- Video: Review of etrailer Trailer Brakes - Drivers Side Brake Assembly - AKEBRK-35L-SA
- Q&A: Can Hydraulic Disc or Electric Drum Brakes Be Added to Demco Tow Dolly
- Video: Replacement Fender Assembly for Demco Kar Kaddy 260/360 Tow Dolly: The Breakdown
- Video: All You Need to Know About the Kodiak Disc Brakes
- Search Results: measure wheel bearings
- Search Results: disk brake pads
- Search Results: trailer hubs and drums
- Search Results: dexter wheel bearings
- Article: Trailer Wiring Diagrams


Mike
7/25/2024
Ok. I have the U-Haul style closed wheel bearing that have 4 bolt holes that bolt to the trailer. Is that the same or able to be used as a flange?