Replacement Brake Shoes For Dexter K23-429-00 & K23-428-00 Trailer Brake Assemblies

Question

Question:

Im trying to find the following brake shoes for a K23-429-00 12 1/4 x 2 1/2 7.2k axle 4 bolt pattern.

asked by: Michael B

0

Expert Reply:

We have the Brake Shoes # BP04-238 for the Dexter RH Brake Assembly # 23-429. We also have the Brake Shoes # BP04-236 if you also need them for the Dexter LH Brake Assembly # 23-428

expert reply by: Bud M

0

Robin H.

2/3/2026

Hey, how did the brake shoes work out for your 7.2K axle setup? Knowing which ones fit best could really help others matching parts for their Dexter brakes.

Answer 1

Thanks for your question, Bill. This one might be a bit tricky to answer, since we don’t carry Fortron or LiFePO4 products, so my resources are a bit limited. I searched around for info on the Fortron TP3SS-55, but unfortunately wasn’t able to find…

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

For a 12-1/4" x 2-1/2" Dexter electric brake assembly you will need the following parts: Left Hand - 12-1/4" x 2-1/2" Brake Shoe and Lining for Dexter - item #BP04-236 Right Hand - 12-1/4" x 2-1/2" Brake Shoe and Lining…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 6

For 7,000 lb Dexter hub assemblies, you could have 1/2 inch or 9/16 inch, or 5/8 inch drive in studs. I've linked the page of our drive in wheel studs for you. Once you have the right stud based on your measurements you can get the correct lug to…

view full answer...

Answer 7

It looks like you recently purchased some Kodiak Wheel Bolts #K58WB316 and 5/8" flange nuts #95188 from us, so thank you for being a loyal customer! What you'll want to torque those to will depend on the construction of your wheels and the…

view full answer...

Answer 8

We only have the nut and washer sold with the hitch ball like the B&W #BWHB94006. This gooseneck ball has a shank 1-1/2" in diameter by 2-3/4" long.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Brake Shoes For Dexter K23-429-00 & K23-428-00 Trailer Brake Assemblies

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching