Replacement Brake Shoe's, Springs, and Screw for 12-1/4" x 2-1/2" Dexter Electric Brake Assembly

Question

Question:

looking for shoes for a dexter 7200lb axle 12-1/4x2-1/2, spring kit,and adjuster thanks for you time

asked by: Michael S

0

Expert Reply:

For a 12-1/4" x 2-1/2" Dexter electric brake assembly you will need the following parts:

Left Hand - 12-1/4" x 2-1/2" Brake Shoe and Lining for Dexter - item # BP04-236

Right Hand - 12-1/4" x 2-1/2" Brake Shoe and Lining for Dexter - item # BP04-238

Replacement Adjusting Screw and Spring for Dexter 12-1/4 x 2-1/2 Electric Brake Assemblies item # K71-411-00

Replacement Brake Spring Kit for Dexter 12-1/4" Electric Brake Assemblies item # K71-506-00

expert reply by: Jerred H

0

Jerred H.

2/17/2026

Hey, how did the new brake shoes and spring kit work out on your Dexter 7200 lb axle? Knowing how the fit and performance turned out could help others working on the same setup.

Answer 1

We have the Brake Shoes #BP04-238 for the Dexter RH Brake Assembly #23-429. We also have the Brake Shoes #BP04-236 if you also need them for the Dexter LH Brake Assembly #23-428

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

It looks like you recently purchased some Kodiak Wheel Bolts #K58WB316 and 5/8" flange nuts #95188 from us, so thank you for being a loyal customer! What you'll want to torque those to will depend on the construction of your wheels and the…

view full answer...

Answer 4

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 5

For 7,000 lb Dexter hub assemblies, you could have 1/2 inch or 9/16 inch, or 5/8 inch drive in studs. I've linked the page of our drive in wheel studs for you. Once you have the right stud based on your measurements you can get the correct lug to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...