Are the TruXedo TS Rails Compatible W/ a Toptiny Tonneau Cover

Question

Question:

I have a 2023 Tundra and want to use the Truxedo TS Rails with the Yakima Overhaul bed rack, but first i need to know if the Truxedo TS Rails are compatible with the Toptiny hard folding tonneau cover.

asked by: Jeff R

0

Expert Reply:

Hey Jeff unfortunately they are not going to be compatible. You'd instead need to use a compatible tonneau cover like the TruXedo Lo Pro Soft Tonneau Cover # TX45DV, and then you'd be able to add the TS rails # TH85FR.

expert reply by: Bryce D

0

Chris R.

2/3/2026

Hey Jeff, did you end up going with the Lo Pro cover and TS rails for your Tundra? Knowing how that setup worked could help others trying to pair a rack with their tonneau cover.

Jeff R.

2/3/2026

I ended up buying a trailer for the kayaks. It was cheaper than buying the low pro cover and the ts rails and now I don't have to worry about lifting them up on the back of the truck.

Chris R.

2/3/2026

@JeffR Nice! Much easier loading. Also don't need to worry about scratching up the truck.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Are the TruXedo TS Rails Compatible W/ a Toptiny Tonneau Cover

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching