Replacement Rail Clamps For a Pace Edwards SwitchBlade Retractable Tonneau Cover

Question

Question:

Hello, wondering if you would happen to have the rail clamps for a Pace-Edwards Switchblade Model Sw2053. Its for a 2017-2020 tundra. I can send pictures for examples if needed.

asked by: Jesus F

0

Expert Reply:

You are going to need the Replacement Rail Clamps # 311-TRPT1250-1 for the Pace Edwards SwitchBlade Retractable Tonneau Cover which fits your 2020 Toyota Tundra. The part number you gave me identifies the canister.

expert reply by: Bud M

0

Answer 1

Yes, we sell both of the parts you are looking for in the attached photo. These two parts are the Replacement Clamps for Extang Trifecta Soft Tonneau Covers part #EX2244-0204 and the Replacement Tail Clamp Assembly for Extang Trifecta 2.0 Tonneau…

view full answer...

Answer 2

Yes, the Trifecta ALX Soft Tonneau Bed Cover item #EX93CV is a way better cover in my opinion. You can secure it when you lock your Frontier's tailgate. The Extang Trifecta 2.0 item #EX89CV does not include the auto-latching system. It just…

view full answer...

Answer 3

The Replacement Clamps for Extang Trifecta Soft Tonneau Covers #EX2244-0204 will indeed fit the factory track system on a 2021 Nissan Frontier. While this may work, it is not technically designed for your Tonno Pro hard fold #TPHF-452. We do not…

view full answer...

Answer 4

IF you're finding that the clamps #EX2244-0204 are too small and don't fit the bed rails on your vehicle, you can trim the plastic to get the clamp to fit. I've attached a snippet from the installation instructions showing Extang giving…

view full answer...

Answer 5

Replacement Sliding Clamp Assembly for Extang eMAX Soft Tonneau Cover #EX1104 comes with both clamps, not just one. I attached a demonstration video which goes over this clamp and shows how two are included.

view full answer...

Answer 6

I attached a picture of what the rail clamps part #311-TRPT1250-1 that you referenced look like installed.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Rail Clamps For a Pace Edwards SwitchBlade Retractable Tonneau Cover

Product Page this Question was Asked From

Continue Researching