Replacement Brake Shoes For Dexter 8-283 Trailer Hub Brake Assembly

Question

Question:

Hi I am looking for replacement brake shoes for a 1994 sandpaper travel trailer by cobra with dexter 8-283 breakes.

asked by: Richard

0

Expert Reply:

Hey Richard,

The Dexter trailer hub 8-283 is a 10" x 1-1/2" design so you would need brake shoe kit # DX78FR for the right-hand side and # DX88FR for the left-hand side.

expert reply by: Kevin C

0

Answer 1

Based on the images with the measurements you sent the Brake Shoe/Lining #bp04-065, Brake Spring Set #K71-362-00, and Magnet Kit #AKBRKR-M10 are the correct replacement parts for the brakes on your 1998 Nash 20N. We do have the Brake Mounting Flange…

view full answer...

Answer 2

The Lippert Components Heavy-Duty Replacement Shock - Yellow #LC283280 is 8.625 inches compressed and 13.5 inches fully extended. Your current suspension may extend and retract slightly further but the shocks will be a good replacement based on the…

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

Hey Dave we do offer replacement brake shoes for your Dexter Electric Trailer Brakes Left/Right Hand Assemblies item #K23-472-473-00. They are the 10" x 1-1/2" Electric Brake Shoe/Lining One Wheel item #bp04-065. You'll need two sets to…

view full answer...

Answer 5

Yes, we do Dave! To replace just the brake shoes on the Dexter Electric Trailer Brakes Left/Right Hand Assemblies item #K23-472-473-00, you'll want the 10" x 1-1/2" Electric Brake Shoe/Lining One Wheel item #bp04-065. These are sold…

view full answer...

Answer 6

Like you said, 10 x 1-1/2 inch brakes are hard to find. We currently do not offer any in that size. But the shoes, #bp04-065, are a fit for Dexter 10 x 1-1/2 inch brakes. The issue is that the axles associated with the Dexter 10 x 1-1/2 inch brakes…

view full answer...

Answer 7

I can't recommend using a Dexter brake shoe on a Hayes/Al Ko brake assembly. The parts haven't been tested together for fit, so I honestly couldn't say if they'd work or not. The same would go for the return spring. Our usual…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Brake Shoes For Dexter 8-283 Trailer Hub Brake Assembly

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching